ata_dev_config_ncq_prio() and ata_dev_config_devslp() both access pages
of the IDENTIFY DEVICE data log. Before calling ata_read_log_page(),
make sure to check for the existence of the IDENTIFY DEVICE data log and
of the log page accessed using ata_identify_page_supported(). This
avoids useless error messages from ata_read_log_page() and failures with
some LLDD scsi drivers using libsas.

Reported-by: Nikolay <knv418@gmail.com>
Cc: stable@kernel.org # 5.15
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Tested-by: Matthew Perkowski <mgperkow@gmail.com>

AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.

commit b1a9585 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix.  Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.

Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

The StorageD3Enable _DSD is used for the vendor to indicate that the disk
should be opted into or out of a different behavior based upon the platform
design.

For AMD's Renoir and Green Sardine platforms it's important that any
attached SATA storage has transitioned into DevSlp when s2idle is used.

If the disk is left in active/partial/slumber, then the system is not able
to resume properly.

When the StorageD3Enable _DSD is detected, check the system is using s2idle
and DevSlp is enabled and if so explicitly wait long enough for the disk to
enter DevSlp.

Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Link: https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/power-management-for-storage-hardware-devices-intro
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

Since ata_ncq_sdev_attrs is a local struct, declare it static. This
avoids a sparse warning at compile time.

Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

To pick the changes from:

  eec2113 ("x86/fpu/amx: Define AMX state components and have it used for boot-time checks")

This only causes these perf files to be rebuilt:

  CC       /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o
  CC       /tmp/build/perf/bench/mem-memset-x86-64-asm.o

And addresses this perf build warning:

  Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
  diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h

Cc: Borislav Petkov <bp@suse.de>
Cc: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

To pick the changes in:

  b566393 ("KVM: SEV: Add support for SEV intra host migration")
  e615e35 ("KVM: x86: On emulation failure, convey the exit reason, etc. to userspace")
  a9d496d ("KVM: x86: Clarify the kvm_run.emulation_failure structure layout")
  c68dc1b ("KVM: x86: Report host tsc and realtime values in KVM_GET_CLOCK")
  dea8ee3 ("RISC-V: KVM: Add SBI v0.1 support")

That just rebuilds perf, as these patches don't add any new KVM ioctl to
be harvested for the the 'perf trace' ioctl syscall argument
beautifiers.

This is also by now used by tools/testing/selftests/kvm/, a simple test
build succeeded.

This silences this perf build warning:

  Warning: Kernel ABI header at 'tools/include/uapi/linux/kvm.h' differs from latest version at 'include/uapi/linux/kvm.h'
  diff -u tools/include/uapi/linux/kvm.h include/uapi/linux/kvm.h

Cc: Anup Patel <anup@brainfault.org>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: David Edmondson <david.edmondson@oracle.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Gonda <pgonda@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Fixing these build problems:

  tests/wp.c:24:12: error: 'wp_read' defined but not used [-Werror=unused-function]
   static int wp_read(int fd, long long *count, int size)
              ^
  tests/wp.c:35:13: error: 'get__perf_event_attr' defined but not used [-Werror=unused-function]
   static void get__perf_event_attr(struct perf_event_attr *attr, int wp_type,
               ^
    CC      /tmp/build/perf/util/print_binary.o

Fixes: e47c6ec ("perf test: Convert watch point tests to test cases.")
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Brendan Higgins <brendanhiggins@google.com>
Cc: Daniel Latypov <dlatypov@google.com>
Cc: David Gow <davidgow@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sohaib Mohamed <sohaib.amhmd@gmail.com>
Cc: Stephane Eranian <eranian@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

As it is being used in tools/perf/arch/arm64/util/arm-spe.c and the
COMPAT_NEED_REALLOCARRAY was only being set when CORESIGHT=1 is set.

Fixes: 56c31cd ("perf arm-spe: Implement find_snapshot callback")
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: German Gomez <german.gomez@arm.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/all/YZT63mIc7iY01er3@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Currently, the 'weight' field in the perf sample has latency information
for some instructions like in memory accesses.  And perf tool has 'weight'
and 'local_weight' sort keys to display the info.

But it's somewhat confusing what it shows exactly.  In my understanding,
'local_weight' shows a weight in a single sample, and (global) 'weight'
shows a sum of the weights in the hist_entry.

For example:

  $ perf mem record -t load dd if=/dev/zero of=/dev/null bs=4k count=1M

  $ perf report --stdio -n -s +local_weight
  ...
  #
  # Overhead  Samples  Command  Shared Object     Symbol                     Local Weight
  # ........  .......  .......  ................  .........................  ............
  #
      21.23%      313  dd       [kernel.vmlinux]  [k] lockref_get_not_zero   32
      12.43%      183  dd       [kernel.vmlinux]  [k] lockref_get_not_zero   35
      11.97%      159  dd       [kernel.vmlinux]  [k] lockref_get_not_zero   36
      10.40%      141  dd       [kernel.vmlinux]  [k] lockref_put_return     32
       7.63%      113  dd       [kernel.vmlinux]  [k] lockref_get_not_zero   33
       6.37%       92  dd       [kernel.vmlinux]  [k] lockref_get_not_zero   34
       6.15%       90  dd       [kernel.vmlinux]  [k] lockref_put_return     33
  ...

So let's look at the 'lockref_get_not_zero' symbols.  The top entry
shows that 313 samples were captured with 'local_weight' 32, so the
total weight should be 313 x 32 = 10016.  But it's not the case:

  $ perf report --stdio -n -s +local_weight,weight -S lockref_get_not_zero
  ...
  #
  # Overhead  Samples  Command  Shared Object     Local Weight  Weight
  # ........  .......  .......  ................  ............  ......
  #
       1.36%        4  dd       [kernel.vmlinux]  36            144
       0.47%        4  dd       [kernel.vmlinux]  37            148
       0.42%        4  dd       [kernel.vmlinux]  32            128
       0.40%        4  dd       [kernel.vmlinux]  34            136
       0.35%        4  dd       [kernel.vmlinux]  36            144
       0.34%        4  dd       [kernel.vmlinux]  35            140
       0.30%        4  dd       [kernel.vmlinux]  36            144
       0.30%        4  dd       [kernel.vmlinux]  34            136
       0.30%        4  dd       [kernel.vmlinux]  32            128
       0.30%        4  dd       [kernel.vmlinux]  32            128
  ...

With the 'weight' sort key, it's divided to 4 samples even with the same
info ('comm', 'dso', 'sym' and 'local_weight').  I don't think this is
what we want.

I found this because of the way it aggregates the 'weight' value.  Since
it's not a period, we should not add them in the he->stat.  Otherwise,
two 32 'weight' entries will create a 64 'weight' entry.

After that, new 32 'weight' samples don't have a matching entry so it'd
create a new entry and make it a 64 'weight' entry again and again.
Later, they will be merged into 128 'weight' entries during the
hists__collapse_resort() with 4 samples, multiple times like above.

Let's keep the weight and display it differently.  For 'local_weight',
it can show the weight as is, and for (global) 'weight' it can display
the number multiplied by the number of samples.

With this change, I can see the expected numbers.

  $ perf report --stdio -n -s +local_weight,weight -S lockref_get_not_zero
  ...
  #
  # Overhead  Samples  Command  Shared Object     Local Weight  Weight
  # ........  .......  .......  ................  ............  .....
  #
      21.23%      313  dd       [kernel.vmlinux]  32            10016
      12.43%      183  dd       [kernel.vmlinux]  35            6405
      11.97%      159  dd       [kernel.vmlinux]  36            5724
       7.63%      113  dd       [kernel.vmlinux]  33            3729
       6.37%       92  dd       [kernel.vmlinux]  34            3128
       4.17%       59  dd       [kernel.vmlinux]  37            2183
       0.08%        1  dd       [kernel.vmlinux]  269           269
       0.08%        1  dd       [kernel.vmlinux]  38            38

Reviewed-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20211105225617.151364-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Handle 'ins_lat' (for instruction latency) and 'local_ins_lat' sort keys
with the same rationale as for the 'weight' and 'local_weight', see the
previous fix in this series for a full explanation.

But I couldn't test it actually, so only build tested.

Reviewed-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20211105225617.151364-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

andle 'p_stage_cyc' (for pipeline stage cycles) sort key with the same
rationale as for the 'weight' and 'local_weight', see the fix in this
series for a full explanation.

Not sure it also needs the local and global variants.

But I couldn't test it actually because I don't have the machine.

Reviewed-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20211105225617.151364-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

To pick the changes in:

  828ca89 ("KVM: x86: Expose TSC offset controls to userspace")

That just rebuilds kvm-stat.c on x86, no change in functionality.

This silences these perf build warning:

  Warning: Kernel ABI header at 'tools/arch/x86/include/uapi/asm/kvm.h' differs from latest version at 'arch/x86/include/uapi/asm/kvm.h'
  diff -u tools/arch/x86/include/uapi/asm/kvm.h arch/x86/include/uapi/asm/kvm.h

Cc: Oliver Upton <oupton@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Commit 10269a2 ("perf test sample-parsing: Add endian test for
struct branch_flags") broke the test case 27 (Sample parsing) on s390 on
linux-next tree:

  # perf test -Fv 27
  27: Sample parsing
  --- start ---
  parsing failed for sample_type 0x800
  ---- end ----
  Sample parsing: FAILED!
  #

The cause of the failure is a wrong #define BS_EXPECTED_BE statement in
above commit.  Correct this define and the test case runs fine.

Output After:

  # perf test -Fv 27
  27: Sample parsing                                                  :
  --- start ---
  ---- end ----
  Sample parsing: Ok
  #

Fixes: 10269a2 ("perf test sample-parsing: Add endian test for struct branch_flags")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Tested-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Acked-by: Madhavan Srinivasan <maddy@linux.ibm.com>
CC: Sven Schnelle <svens@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/54077e81-503e-3405-6cb0-6541eb5532cc@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

ASan reports memory leaks while running:

  $ perf bench sched all

Fixes: e27454c ("perf bench: Add sched-messaging.c: Benchmark for scheduler and IPC mechanisms based on hackbench")
Signed-off-by: Sohaib Mohamed <sohaib.amhmd@gmail.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Russel <rusty@rustcorp.com.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pierre Gondois <pierre.gondois@arm.com>
Link: http://lore.kernel.org/lkml/20211110022012.16620-1-sohaib.amhmd@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

'perf inject' is currently not working for Arm SPE. When you try to run
'perf inject' and 'perf report' with a perf.data file that contains SPE
traces, the tool reports a "Bad address" error:

  # ./perf record -e arm_spe_0/ts_enable=1,store_filter=1,branch_filter=1,load_filter=1/ -a -- sleep 1
  # ./perf inject -i perf.data -o perf.inject.data --itrace
  # ./perf report -i perf.inject.data --stdio

  0x42c00 [0x8]: failed to process type: 9 [Bad address]
  Error:
  failed to process sample

As far as I know, the issue was first spotted in [1], but 'perf inject'
was not yet injecting the samples. This patch does something similar to
what cs_etm does for injecting the samples [2], but for SPE.

[1] https://patchwork.kernel.org/project/linux-arm-kernel/cover/20210412091006.468557-1-leo.yan@linaro.org/#24117339
[2] https://git.kernel.org/pub/scm/linux/kernel/git/acme/linux.git/tree/tools/perf/util/cs-etm.c?h=perf/core&id=133fe2e617e48ca0948983329f43877064ffda3e#n1196

Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: German Gomez <german.gomez@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20211105104130.28186-2-german.gomez@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

…ection

The patch removing the feature-sync-compare-and-swap feature detection
didn't remove the call to main_test_sync_compare_and_swap(), making the
'test-all' case fail an all the feature tests to be performed
individually:

  $ cat /tmp/build/perf/feature/test-all.make.output
  In file included from test-all.c:18:
  test-libpython-version.c:5:10: error: #error
      5 |         #error
        |          ^~~~~
  test-all.c: In function ‘main’:
  test-all.c:203:9: error: implicit declaration of function ‘main_test_sync_compare_and_swap’ [-Werror=implicit-function-declaration]
    203 |         main_test_sync_compare_and_swap(argc, argv);
        |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  cc1: all warnings being treated as errors
  $

Fix it, now to figure out what is that test-libpython-version.c
problem...

Fixes: 60fa754 ("tools: Remove feature-sync-compare-and-swap feature detection")
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/YZU9Fe0sgkHSXeC2@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

…_waitv syscall

To pick the changes in these csets:

  b3ff288 ("MIPS: syscalls: Wire up futex_waitv syscall")

That add support for this new syscall in tools such as 'perf trace'.

For instance, this is now possible (adapted from the x86_64 test output):

  # perf trace -e futex_waitv
  ^C#
  # perf trace -v -e futex_waitv
  event qualifier tracepoint filter: (common_pid != 807333 && common_pid != 3564) && (id == 449)
  ^C#
  # perf trace -v -e futex* --max-events 10
  event qualifier tracepoint filter: (common_pid != 812168 && common_pid != 3564) && (id == 202 || id == 449)
  mmap size 528384B
           ? (         ): Timer/219310  ... [continued]: futex())                                            = -1 ETIMEDOUT (Connection timed out)
       0.012 ( 0.002 ms): Timer/219310 futex(uaddr: 0x7fd0b152d3c8, op: WAKE|PRIVATE_FLAG, val: 1)           = 0
       0.024 ( 0.060 ms): Timer/219310 futex(uaddr: 0x7fd0b152d420, op: WAIT_BITSET|PRIVATE_FLAG, utime: 0x7fd0b1657840, val3: MATCH_ANY) = 0
       0.086 ( 0.001 ms): Timer/219310 futex(uaddr: 0x7fd0b152d3c8, op: WAKE|PRIVATE_FLAG, val: 1)           = 0
       0.088 (         ): Timer/219310 futex(uaddr: 0x7fd0b152d424, op: WAIT_BITSET|PRIVATE_FLAG, utime: 0x7fd0b1657840, val3: MATCH_ANY) ...
       0.075 ( 0.005 ms): Web Content/219299 futex(uaddr: 0x7fd0b152d420, op: WAKE|PRIVATE_FLAG, val: 1)     = 1
       0.169 ( 0.004 ms): Web Content/219299 futex(uaddr: 0x7fd0b152d424, op: WAKE|PRIVATE_FLAG, val: 1)     = 1
       0.088 ( 0.089 ms): Timer/219310  ... [continued]: futex())                                            = 0
       0.179 ( 0.001 ms): Timer/219310 futex(uaddr: 0x7fd0b152d3c8, op: WAKE|PRIVATE_FLAG, val: 1)           = 0
       0.181 (         ): Timer/219310 futex(uaddr: 0x7fd0b152d420, op: WAIT_BITSET|PRIVATE_FLAG, utime: 0x7fd0b1657840, val3: MATCH_ANY) ...
  #

That is the filter expression attached to the raw_syscalls:sys_{enter,exit}
tracepoints.

  $ grep futex_waitv tools/perf/arch/mips/entry/syscalls/syscall_n64.tbl
  449	n64	futex_waitv			sys_futex_waitv
  $

This addresses these perf build warnings:

  Warning: Kernel ABI header at 'tools/perf/arch/mips/entry/syscalls/syscall_n64.tbl' differs from latest version at 'arch/mips/kernel/syscalls/syscall_n64.tbl'
  diff -u tools/perf/arch/mips/entry/syscalls/syscall_n64.tbl arch/mips/kernel/syscalls/syscall_n64.tbl

Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Wang Haojun <jiangliuer01@gmail.com>
Link: https://lore.kernel.org/lkml/YZZRxuIyvSGLZhM4@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf_hpp__column_unregister() removes an entry from a list but doesn't
free the memory causing a memory leak spotted by leak sanitizer.

Add the free while at the same time reducing the scope of the function
to static.

Signed-off-by: Ian Rogers <irogers@google.com>
Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20211118071247.2140392-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf_tip() may allocate memory or use a literal, this means memory
wasn't freed if allocated. Change the API so that literals aren't used.

At the same time add missing frees for system_path. These issues were
spotted using leak sanitizer.

Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20211118073804.2149974-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

unit may have a strdup pointer or be to a literal, consequently memory
assocciated with it isn't freed. Change it so the unit is always strdup
and so the memory can be safely freed.

Fix related issue in perf_event__process_event_update() for name and
own_cpus. Leaks were spotted by leak sanitizer.

Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20211118084749.2191447-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Calling destroy_hist_field() on an expression will recursively free
any operands associated with the expression. If during expression
parsing the operands of the expression are already set when an error
is encountered, there is no need to explicity free the operands. Doing
so will result in destroy_hist_field() being called twice for the
operands and lead to a use-after-free (UAF) error.

If the operands are associated with the expression, only call
destroy_hist_field() on the expression since the operands will be
recursively freed.

Link: https://lore.kernel.org/all/CAHk-=wgcrEbFgkw9720H3tW-AhHOoEKhYwZinYJw4FpzSaJ6_Q@mail.gmail.com/
Link: https://lkml.kernel.org/r/20211118011542.1420131-1-kaleshsingh@google.com

Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Kalesh Singh <kaleshsingh@google.com>
Fixes: 8b5d46f ("tracing/histogram: Optimize division by constants")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.

Use memset_startat() to avoid confusing memset() about writing beyond
the target struct member.

Link: https://lkml.kernel.org/r/20211118202217.1285588-1-keescook@chromium.org

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

If trace_seq becomes full, trace_seq_vprintf() no longer consumes
arguments from va_list, making va_list out of sync with format
processing by trace_check_vprintf().

This causes va_arg() in trace_check_vprintf() to return wrong
positional argument, which results into a WARN_ON_ONCE() hit.

ftrace_stress_test from LTP triggers this situation.

Fix it by explicitly avoiding further use if va_list at the point
when it's consistency can no longer be guaranteed.

Link: https://lkml.kernel.org/r/20211118145516.13219-1-nikita.yushchenko@virtuozzo.com

Signed-off-by: Nikita Yushchenko <nikita.yushchenko@virtuozzo.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

….org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix the 'local_weight', 'weight' (memory access latency),
   'local_ins_lat', 'ins_lat' (instruction latency) and 'pstage_cyc'
   (pipeline stage cycles) sort key sample aggregation.

 - Fix 'perf test' entry for watchpoints on s/390.

 - Fix branch_stack entry endianness check in the 'perf test' sample
   parsing test.

 - Fix ARM SPE handling on 'perf inject'.

 - Fix memory leaks detected with ASan.

 - Fix build on arm64 related to reallocarray() availability.

 - Sync copies of kernel headers: cpufeatures, kvm, MIPS syscalltable
   (futex_waitv).

* tag 'perf-tools-fixes-for-v5.16-2021-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf evsel: Fix memory leaks relating to unit
  perf report: Fix memory leaks around perf_tip()
  perf hist: Fix memory leak of a perf_hpp_fmt
  tools headers UAPI: Sync MIPS syscall table file changed by new futex_waitv syscall
  tools build: Fix removal of feature-sync-compare-and-swap feature detection
  perf inject: Fix ARM SPE handling
  perf bench: Fix two memory leaks detected with ASan
  perf test sample-parsing: Fix branch_stack entry endianness check
  tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
  perf sort: Fix the 'p_stage_cyc' sort key behavior
  perf sort: Fix the 'ins_lat' sort key behavior
  perf sort: Fix the 'weight' sort key behavior
  perf tools: Set COMPAT_NEED_REALLOCARRAY for CONFIG_AUXTRACE=1
  perf tests wp: Remove unused functions on s390
  tools headers UAPI: Sync linux/kvm.h with the kernel sources
  tools headers cpufeatures: Sync with the kernel sources

…l/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:

 - Fix double free in destroy_hist_field

 - Harden memset() of trace_iterator structure

 - Do not warn in trace printk check when test buffer fills up

* tag 'trace-v5.16-6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Don't use out-of-sync va_list in event printing
  tracing: Use memset_startat() to zero struct trace_iterator
  tracing/histogram: Fix UAF in destroy_hist_field()

…nel/git/dlemoal/libata

Pull libata fixes from Damien Le Moal:

 - Prevent accesses to unsupported log pages as that causes device scan
   failures with LLDDs using libsas (from me).

 - A couple of fixes for AMD AHCI adapters handling of low power modes
   and resume (from Mario).

 - Fix a compilation warning (from me).

* tag 'libata-5.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  ata: libata-sata: Declare ata_ncq_sdev_attrs static
  ata: libahci: Adjust behavior when StorageD3Enable _DSD is set
  ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile
  ata: libata: add missing ata_identify_page_supported() calls
  ata: libata: improve ata_read_log_page() error message