Merge pull request #2 from gregkh/master #4

cnspary · 2021-09-17T14:22:02Z

update

As previously noted in commit 66e4f4a ("rtc: cmos: Use spin_lock_irqsave() in cmos_interrupt()"): <4>[ 254.192378] WARNING: inconsistent lock state <4>[ 254.192384] 5.12.0-rc1-CI-CI_DRM_9834+ #1 Not tainted <4>[ 254.192396] -------------------------------- <4>[ 254.192400] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. <4>[ 254.192409] rtcwake/5309 [HC0[0]:SC0[0]:HE1:SE1] takes: <4>[ 254.192429] ffffffff8263c5f8 (rtc_lock){?...}-{2:2}, at: cmos_interrupt+0x18/0x100 <4>[ 254.192481] {IN-HARDIRQ-W} state was registered at: <4>[ 254.192488] lock_acquire+0xd1/0x3d0 <4>[ 254.192504] _raw_spin_lock+0x2a/0x40 <4>[ 254.192519] cmos_interrupt+0x18/0x100 <4>[ 254.192536] rtc_handler+0x1f/0xc0 <4>[ 254.192553] acpi_ev_fixed_event_detect+0x109/0x13c <4>[ 254.192574] acpi_ev_sci_xrupt_handler+0xb/0x28 <4>[ 254.192596] acpi_irq+0x13/0x30 <4>[ 254.192620] __handle_irq_event_percpu+0x43/0x2c0 <4>[ 254.192641] handle_irq_event_percpu+0x2b/0x70 <4>[ 254.192661] handle_irq_event+0x2f/0x50 <4>[ 254.192680] handle_fasteoi_irq+0x9e/0x150 <4>[ 254.192693] __common_interrupt+0x76/0x140 <4>[ 254.192715] common_interrupt+0x96/0xc0 <4>[ 254.192732] asm_common_interrupt+0x1e/0x40 <4>[ 254.192750] _raw_spin_unlock_irqrestore+0x38/0x60 <4>[ 254.192767] resume_irqs+0xba/0xf0 <4>[ 254.192786] dpm_resume_noirq+0x245/0x3d0 <4>[ 254.192811] suspend_devices_and_enter+0x230/0xaa0 <4>[ 254.192835] pm_suspend.cold.8+0x301/0x34a <4>[ 254.192859] state_store+0x7b/0xe0 <4>[ 254.192879] kernfs_fop_write_iter+0x11d/0x1c0 <4>[ 254.192899] new_sync_write+0x11d/0x1b0 <4>[ 254.192916] vfs_write+0x265/0x390 <4>[ 254.192933] ksys_write+0x5a/0xd0 <4>[ 254.192949] do_syscall_64+0x33/0x80 <4>[ 254.192965] entry_SYSCALL_64_after_hwframe+0x44/0xae <4>[ 254.192986] irq event stamp: 43775 <4>[ 254.192994] hardirqs last enabled at (43775): [<ffffffff81c00c42>] asm_sysvec_apic_timer_interrupt+0x12/0x20 <4>[ 254.193023] hardirqs last disabled at (43774): [<ffffffff81aa691a>] sysvec_apic_timer_interrupt+0xa/0xb0 <4>[ 254.193049] softirqs last enabled at (42548): [<ffffffff81e00342>] __do_softirq+0x342/0x48e <4>[ 254.193074] softirqs last disabled at (42543): [<ffffffff810b45fd>] irq_exit_rcu+0xad/0xd0 <4>[ 254.193101] other info that might help us debug this: <4>[ 254.193107] Possible unsafe locking scenario: <4>[ 254.193112] CPU0 <4>[ 254.193117] ---- <4>[ 254.193121] lock(rtc_lock); <4>[ 254.193137] <Interrupt> <4>[ 254.193142] lock(rtc_lock); <4>[ 254.193156] *** DEADLOCK *** <4>[ 254.193161] 6 locks held by rtcwake/5309: <4>[ 254.193174] #0: ffff888104861430 (sb_writers#5){.+.+}-{0:0}, at: ksys_write+0x5a/0xd0 <4>[ 254.193232] #1: ffff88810f823288 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0xe7/0x1c0 <4>[ 254.193282] #2: ffff888100cef3c0 (kn->active#285 <7>[ 254.192706] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <4>[ 254.193307] ){.+.+}-{0:0}, at: kernfs_fop_write_iter+0xf0/0x1c0 <4>[ 254.193333] #3: ffffffff82649fa8 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend.cold.8+0xce/0x34a <4>[ 254.193387] #4: ffffffff827a2108 (acpi_scan_lock){+.+.}-{3:3}, at: acpi_suspend_begin+0x47/0x70 <4>[ 254.193433] #5: ffff8881019ea178 (&dev->mutex){....}-{3:3}, at: device_resume+0x68/0x1e0 <4>[ 254.193485] stack backtrace: <4>[ 254.193492] CPU: 1 PID: 5309 Comm: rtcwake Not tainted 5.12.0-rc1-CI-CI_DRM_9834+ #1 <4>[ 254.193514] Hardware name: Google Soraka/Soraka, BIOS MrChromebox-4.10 08/25/2019 <4>[ 254.193524] Call Trace: <4>[ 254.193536] dump_stack+0x7f/0xad <4>[ 254.193567] mark_lock.part.47+0x8ca/0xce0 <4>[ 254.193604] __lock_acquire+0x39b/0x2590 <4>[ 254.193626] ? asm_sysvec_apic_timer_interrupt+0x12/0x20 <4>[ 254.193660] lock_acquire+0xd1/0x3d0 <4>[ 254.193677] ? cmos_interrupt+0x18/0x100 <4>[ 254.193716] _raw_spin_lock+0x2a/0x40 <4>[ 254.193735] ? cmos_interrupt+0x18/0x100 <4>[ 254.193758] cmos_interrupt+0x18/0x100 <4>[ 254.193785] cmos_resume+0x2ac/0x2d0 <4>[ 254.193813] ? acpi_pm_set_device_wakeup+0x1f/0x110 <4>[ 254.193842] ? pnp_bus_suspend+0x10/0x10 <4>[ 254.193864] pnp_bus_resume+0x5e/0x90 <4>[ 254.193885] dpm_run_callback+0x5f/0x240 <4>[ 254.193914] device_resume+0xb2/0x1e0 <4>[ 254.193942] ? pm_dev_err+0x25/0x25 <4>[ 254.193974] dpm_resume+0xea/0x3f0 <4>[ 254.194005] dpm_resume_end+0x8/0x10 <4>[ 254.194030] suspend_devices_and_enter+0x29b/0xaa0 <4>[ 254.194066] pm_suspend.cold.8+0x301/0x34a <4>[ 254.194094] state_store+0x7b/0xe0 <4>[ 254.194124] kernfs_fop_write_iter+0x11d/0x1c0 <4>[ 254.194151] new_sync_write+0x11d/0x1b0 <4>[ 254.194183] vfs_write+0x265/0x390 <4>[ 254.194207] ksys_write+0x5a/0xd0 <4>[ 254.194232] do_syscall_64+0x33/0x80 <4>[ 254.194251] entry_SYSCALL_64_after_hwframe+0x44/0xae <4>[ 254.194274] RIP: 0033:0x7f07d79691e7 <4>[ 254.194293] Code: 64 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24 <4>[ 254.194312] RSP: 002b:00007ffd9cc2c768 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 <4>[ 254.194337] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007f07d79691e7 <4>[ 254.194352] RDX: 0000000000000004 RSI: 0000556ebfc63590 RDI: 000000000000000b <4>[ 254.194366] RBP: 0000556ebfc63590 R08: 0000000000000000 R09: 0000000000000004 <4>[ 254.194379] R10: 0000556ebf0ec2a6 R11: 0000000000000246 R12: 0000000000000004 which breaks S3-resume on fi-kbl-soraka presumably as that's slow enough to trigger the alarm during the suspend. Fixes: 6950d04 ("rtc: cmos: Replace spin_lock_irqsave with spin_lock in hard IRQ") References: 66e4f4a ("rtc: cmos: Use spin_lock_irqsave() in cmos_interrupt()"): Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Xiaofei Tan <tanxiaofei@huawei.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20210305122140.28774-1-chris@chris-wilson.co.uk

It's later supposed to be either a correct address or NULL. Without the initialization, it may contain an undefined value which results in the following segmentation fault: # perf top --sort comm -g --ignore-callees=do_idle terminates with: #0 0x00007ffff56b7685 in __strlen_avx2 () from /lib64/libc.so.6 gregkh#1 0x00007ffff55e3802 in strdup () from /lib64/libc.so.6 gregkh#2 0x00005555558cb139 in hist_entry__init (callchain_size=<optimized out>, sample_self=true, template=0x7fffde7fb110, he=0x7fffd801c250) at util/hist.c:489 gregkh#3 hist_entry__new (template=template@entry=0x7fffde7fb110, sample_self=sample_self@entry=true) at util/hist.c:564 gregkh#4 0x00005555558cb4ba in hists__findnew_entry (hists=hists@entry=0x5555561d9e38, entry=entry@entry=0x7fffde7fb110, al=al@entry=0x7fffde7fb420, sample_self=sample_self@entry=true) at util/hist.c:657 gregkh#5 0x00005555558cba1b in __hists__add_entry (hists=hists@entry=0x5555561d9e38, al=0x7fffde7fb420, sym_parent=<optimized out>, bi=bi@entry=0x0, mi=mi@entry=0x0, sample=sample@entry=0x7fffde7fb4b0, sample_self=true, ops=0x0, block_info=0x0) at util/hist.c:288 gregkh#6 0x00005555558cbb70 in hists__add_entry (sample_self=true, sample=0x7fffde7fb4b0, mi=0x0, bi=0x0, sym_parent=<optimized out>, al=<optimized out>, hists=0x5555561d9e38) at util/hist.c:1056 gregkh#7 iter_add_single_cumulative_entry (iter=0x7fffde7fb460, al=<optimized out>) at util/hist.c:1056 gregkh#8 0x00005555558cc8a4 in hist_entry_iter__add (iter=iter@entry=0x7fffde7fb460, al=al@entry=0x7fffde7fb420, max_stack_depth=<optimized out>, arg=arg@entry=0x7fffffff7db0) at util/hist.c:1231 gregkh#9 0x00005555557cdc9a in perf_event__process_sample (machine=<optimized out>, sample=0x7fffde7fb4b0, evsel=<optimized out>, event=<optimized out>, tool=0x7fffffff7db0) at builtin-top.c:842 gregkh#10 deliver_event (qe=<optimized out>, qevent=<optimized out>) at builtin-top.c:1202 gregkh#11 0x00005555558a9318 in do_flush (show_progress=false, oe=0x7fffffff80e0) at util/ordered-events.c:244 gregkh#12 __ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP, timestamp=timestamp@entry=0) at util/ordered-events.c:323 gregkh#13 0x00005555558a9789 in __ordered_events__flush (timestamp=<optimized out>, how=<optimized out>, oe=<optimized out>) at util/ordered-events.c:339 gregkh#14 ordered_events__flush (how=OE_FLUSH__TOP, oe=0x7fffffff80e0) at util/ordered-events.c:341 gregkh#15 ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP) at util/ordered-events.c:339 gregkh#16 0x00005555557cd631 in process_thread (arg=0x7fffffff7db0) at builtin-top.c:1114 gregkh#17 0x00007ffff7bb817a in start_thread () from /lib64/libpthread.so.0 gregkh#18 0x00007ffff5656dc3 in clone () from /lib64/libc.so.6 If you look at the frame gregkh#2, the code is: 488 if (he->srcline) { 489 he->srcline = strdup(he->srcline); 490 if (he->srcline == NULL) 491 goto err_rawdata; 492 } If he->srcline is not NULL (it is not NULL if it is uninitialized rubbish), it gets strdupped and strdupping a rubbish random string causes the problem. Also, if you look at the commit 1fb7d06, it adds the srcline property into the struct, but not initializing it everywhere needed. Committer notes: Now I see, when using --ignore-callees=do_idle we end up here at line 2189 in add_callchain_ip(): 2181 if (al.sym != NULL) { 2182 if (perf_hpp_list.parent && !*parent && 2183 symbol__match_regex(al.sym, &parent_regex)) 2184 *parent = al.sym; 2185 else if (have_ignore_callees && root_al && 2186 symbol__match_regex(al.sym, &ignore_callees_regex)) { 2187 /* Treat this symbol as the root, 2188 forgetting its callees. */ 2189 *root_al = al; 2190 callchain_cursor_reset(cursor); 2191 } 2192 } And the al that doesn't have the ->srcline field initialized will be copied to the root_al, so then, back to: 1211 int hist_entry_iter__add(struct hist_entry_iter *iter, struct addr_location *al, 1212 int max_stack_depth, void *arg) 1213 { 1214 int err, err2; 1215 struct map *alm = NULL; 1216 1217 if (al) 1218 alm = map__get(al->map); 1219 1220 err = sample__resolve_callchain(iter->sample, &callchain_cursor, &iter->parent, 1221 iter->evsel, al, max_stack_depth); 1222 if (err) { 1223 map__put(alm); 1224 return err; 1225 } 1226 1227 err = iter->ops->prepare_entry(iter, al); 1228 if (err) 1229 goto out; 1230 1231 err = iter->ops->add_single_entry(iter, al); 1232 if (err) 1233 goto out; 1234 That al at line 1221 is what hist_entry_iter__add() (called from sample__resolve_callchain()) saw as 'root_al', and then: iter->ops->add_single_entry(iter, al); will go on with al->srcline with a bogus value, I'll add the above sequence to the cset and apply, thanks! Signed-off-by: Michael Petlan <mpetlan@redhat.com> CC: Milian Wolff <milian.wolff@kdab.com> Cc: Jiri Olsa <jolsa@redhat.com> Fixes: 1fb7d06 ("perf report Use srcline from callchain for hist entries") Link: https //lore.kernel.org/r/20210719145332.29747-1-mpetlan@redhat.com Reported-by: Juri Lelli <jlelli@redhat.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

FD uses xyarray__entry that may return NULL if an index is out of bounds. If NULL is returned then a segv happens as FD unconditionally dereferences the pointer. This was happening in a case of with perf iostat as shown below. The fix is to make FD an "int*" rather than an int and handle the NULL case as either invalid input or a closed fd. $ sudo gdb --args perf stat --iostat list ... Breakpoint 1, perf_evsel__alloc_fd (evsel=0x5555560951a0, ncpus=1, nthreads=1) at evsel.c:50 50 { (gdb) bt #0 perf_evsel__alloc_fd (evsel=0x5555560951a0, ncpus=1, nthreads=1) at evsel.c:50 gregkh#1 0x000055555585c188 in evsel__open_cpu (evsel=0x5555560951a0, cpus=0x555556093410, threads=0x555556086fb0, start_cpu=0, end_cpu=1) at util/evsel.c:1792 gregkh#2 0x000055555585cfb2 in evsel__open (evsel=0x5555560951a0, cpus=0x0, threads=0x555556086fb0) at util/evsel.c:2045 gregkh#3 0x000055555585d0db in evsel__open_per_thread (evsel=0x5555560951a0, threads=0x555556086fb0) at util/evsel.c:2065 gregkh#4 0x00005555558ece64 in create_perf_stat_counter (evsel=0x5555560951a0, config=0x555555c34700 <stat_config>, target=0x555555c2f1c0 <target>, cpu=0) at util/stat.c:590 gregkh#5 0x000055555578e927 in __run_perf_stat (argc=1, argv=0x7fffffffe4a0, run_idx=0) at builtin-stat.c:833 gregkh#6 0x000055555578f3c6 in run_perf_stat (argc=1, argv=0x7fffffffe4a0, run_idx=0) at builtin-stat.c:1048 gregkh#7 0x0000555555792ee5 in cmd_stat (argc=1, argv=0x7fffffffe4a0) at builtin-stat.c:2534 gregkh#8 0x0000555555835ed3 in run_builtin (p=0x555555c3f540 <commands+288>, argc=3, argv=0x7fffffffe4a0) at perf.c:313 gregkh#9 0x0000555555836154 in handle_internal_command (argc=3, argv=0x7fffffffe4a0) at perf.c:365 gregkh#10 0x000055555583629f in run_argv (argcp=0x7fffffffe2ec, argv=0x7fffffffe2e0) at perf.c:409 gregkh#11 0x0000555555836692 in main (argc=3, argv=0x7fffffffe4a0) at perf.c:539 ... (gdb) c Continuing. Error: The sys_perf_event_open() syscall returned with 22 (Invalid argument) for event (uncore_iio_0/event=0x83,umask=0x04,ch_mask=0xF,fc_mask=0x07/). /bin/dmesg | grep -i perf may provide additional information. Program received signal SIGSEGV, Segmentation fault. 0x00005555559b03ea in perf_evsel__close_fd_cpu (evsel=0x5555560951a0, cpu=1) at evsel.c:166 166 if (FD(evsel, cpu, thread) >= 0) v3. fixes a bug in perf_evsel__run_ioctl where the sense of a branch was backward. Signed-off-by: Ian Rogers <irogers@google.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20210918054440.2350466-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

[ Upstream commit 21e3980 ] vctrl_enable() and vctrl_disable() call regulator_enable() and regulator_disable(), respectively. However, vctrl_* are regulator ops and should not be calling the locked regulator APIs. Doing so results in a lockdep warning. Instead of exporting more internal regulator ops, model the ctrl supply as an actual supply to vctrl-regulator. At probe time this driver still needs to use the consumer API to fetch its constraints, but otherwise lets the regulator core handle the upstream supply for it. The enable/disable/is_enabled ops are not removed, but now only track state internally. This preserves the original behavior with the ops being available, but one could argue that the original behavior was already incorrect: the internal state would not match the upstream supply if that supply had another consumer that enabled the supply, while vctrl-regulator was not enabled. The lockdep warning is as follows: WARNING: possible circular locking dependency detected 5.14.0-rc6 gregkh#2 Not tainted ------------------------------------------------------ swapper/0/1 is trying to acquire lock: ffffffc011306d00 (regulator_list_mutex){+.+.}-{3:3}, at: regulator_lock_dependent (arch/arm64/include/asm/current.h:19 include/linux/ww_mutex.h:111 drivers/regulator/core.c:329) but task is already holding lock: ffffff8004a77160 (regulator_ww_class_mutex){+.+.}-{3:3}, at: regulator_lock_recursive (drivers/regulator/core.c:156 drivers/regulator/core.c:263) which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> gregkh#2 (regulator_ww_class_mutex){+.+.}-{3:3}: __mutex_lock_common (include/asm-generic/atomic-instrumented.h:606 include/asm-generic/atomic-long.h:29 kernel/locking/mutex.c:103 kernel/locking/mutex.c:144 kernel/locking/mutex.c:963) ww_mutex_lock (kernel/locking/mutex.c:1199) regulator_lock_recursive (drivers/regulator/core.c:156 drivers/regulator/core.c:263) regulator_lock_dependent (drivers/regulator/core.c:343) regulator_enable (drivers/regulator/core.c:2808) set_machine_constraints (drivers/regulator/core.c:1536) regulator_register (drivers/regulator/core.c:5486) devm_regulator_register (drivers/regulator/devres.c:196) reg_fixed_voltage_probe (drivers/regulator/fixed.c:289) platform_probe (drivers/base/platform.c:1427) [...] -> gregkh#1 (regulator_ww_class_acquire){+.+.}-{0:0}: regulator_lock_dependent (include/linux/ww_mutex.h:129 drivers/regulator/core.c:329) regulator_enable (drivers/regulator/core.c:2808) set_machine_constraints (drivers/regulator/core.c:1536) regulator_register (drivers/regulator/core.c:5486) devm_regulator_register (drivers/regulator/devres.c:196) reg_fixed_voltage_probe (drivers/regulator/fixed.c:289) [...] -> #0 (regulator_list_mutex){+.+.}-{3:3}: __lock_acquire (kernel/locking/lockdep.c:3052 (discriminator 4) kernel/locking/lockdep.c:3174 (discriminator 4) kernel/locking/lockdep.c:3789 (discriminator 4) kernel/locking/lockdep.c:5015 (discriminator 4)) lock_acquire (arch/arm64/include/asm/percpu.h:39 kernel/locking/lockdep.c:438 kernel/locking/lockdep.c:5627) __mutex_lock_common (include/asm-generic/atomic-instrumented.h:606 include/asm-generic/atomic-long.h:29 kernel/locking/mutex.c:103 kernel/locking/mutex.c:144 kernel/locking/mutex.c:963) mutex_lock_nested (kernel/locking/mutex.c:1125) regulator_lock_dependent (arch/arm64/include/asm/current.h:19 include/linux/ww_mutex.h:111 drivers/regulator/core.c:329) regulator_enable (drivers/regulator/core.c:2808) vctrl_enable (drivers/regulator/vctrl-regulator.c:400) _regulator_do_enable (drivers/regulator/core.c:2617) _regulator_enable (drivers/regulator/core.c:2764) regulator_enable (drivers/regulator/core.c:308 drivers/regulator/core.c:2809) _set_opp (drivers/opp/core.c:819 drivers/opp/core.c:1072) dev_pm_opp_set_rate (drivers/opp/core.c:1164) set_target (drivers/cpufreq/cpufreq-dt.c:62) __cpufreq_driver_target (drivers/cpufreq/cpufreq.c:2216 drivers/cpufreq/cpufreq.c:2271) cpufreq_online (drivers/cpufreq/cpufreq.c:1488 (discriminator 2)) cpufreq_add_dev (drivers/cpufreq/cpufreq.c:1563) subsys_interface_register (drivers/base/bus.c:?) cpufreq_register_driver (drivers/cpufreq/cpufreq.c:2819) dt_cpufreq_probe (drivers/cpufreq/cpufreq-dt.c:344) [...] other info that might help us debug this: Chain exists of: regulator_list_mutex --> regulator_ww_class_acquire --> regulator_ww_class_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(regulator_ww_class_mutex); lock(regulator_ww_class_acquire); lock(regulator_ww_class_mutex); lock(regulator_list_mutex); *** DEADLOCK *** 6 locks held by swapper/0/1: #0: ffffff8002d32188 (&dev->mutex){....}-{3:3}, at: __device_driver_lock (drivers/base/dd.c:1030) gregkh#1: ffffffc0111a0520 (cpu_hotplug_lock){++++}-{0:0}, at: cpufreq_register_driver (drivers/cpufreq/cpufreq.c:2792 (discriminator 2)) gregkh#2: ffffff8002a8d918 (subsys mutex#9){+.+.}-{3:3}, at: subsys_interface_register (drivers/base/bus.c:1033) gregkh#3: ffffff800341bb90 (&policy->rwsem){+.+.}-{3:3}, at: cpufreq_online (include/linux/bitmap.h:285 include/linux/cpumask.h:405 drivers/cpufreq/cpufreq.c:1399) gregkh#4: ffffffc011f0b7b8 (regulator_ww_class_acquire){+.+.}-{0:0}, at: regulator_enable (drivers/regulator/core.c:2808) gregkh#5: ffffff8004a77160 (regulator_ww_class_mutex){+.+.}-{3:3}, at: regulator_lock_recursive (drivers/regulator/core.c:156 drivers/regulator/core.c:263) stack backtrace: CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.14.0-rc6 gregkh#2 7c8f8996d021ed0f65271e6aeebf7999de74a9fa Hardware name: Google Scarlet (DT) Call trace: dump_backtrace (arch/arm64/kernel/stacktrace.c:161) show_stack (arch/arm64/kernel/stacktrace.c:218) dump_stack_lvl (lib/dump_stack.c:106 (discriminator 2)) dump_stack (lib/dump_stack.c:113) print_circular_bug (kernel/locking/lockdep.c:?) check_noncircular (kernel/locking/lockdep.c:?) __lock_acquire (kernel/locking/lockdep.c:3052 (discriminator 4) kernel/locking/lockdep.c:3174 (discriminator 4) kernel/locking/lockdep.c:3789 (discriminator 4) kernel/locking/lockdep.c:5015 (discriminator 4)) lock_acquire (arch/arm64/include/asm/percpu.h:39 kernel/locking/lockdep.c:438 kernel/locking/lockdep.c:5627) __mutex_lock_common (include/asm-generic/atomic-instrumented.h:606 include/asm-generic/atomic-long.h:29 kernel/locking/mutex.c:103 kernel/locking/mutex.c:144 kernel/locking/mutex.c:963) mutex_lock_nested (kernel/locking/mutex.c:1125) regulator_lock_dependent (arch/arm64/include/asm/current.h:19 include/linux/ww_mutex.h:111 drivers/regulator/core.c:329) regulator_enable (drivers/regulator/core.c:2808) vctrl_enable (drivers/regulator/vctrl-regulator.c:400) _regulator_do_enable (drivers/regulator/core.c:2617) _regulator_enable (drivers/regulator/core.c:2764) regulator_enable (drivers/regulator/core.c:308 drivers/regulator/core.c:2809) _set_opp (drivers/opp/core.c:819 drivers/opp/core.c:1072) dev_pm_opp_set_rate (drivers/opp/core.c:1164) set_target (drivers/cpufreq/cpufreq-dt.c:62) __cpufreq_driver_target (drivers/cpufreq/cpufreq.c:2216 drivers/cpufreq/cpufreq.c:2271) cpufreq_online (drivers/cpufreq/cpufreq.c:1488 (discriminator 2)) cpufreq_add_dev (drivers/cpufreq/cpufreq.c:1563) subsys_interface_register (drivers/base/bus.c:?) cpufreq_register_driver (drivers/cpufreq/cpufreq.c:2819) dt_cpufreq_probe (drivers/cpufreq/cpufreq-dt.c:344) [...] Reported-by: Brian Norris <briannorris@chromium.org> Fixes: f8702f9 ("regulator: core: Use ww_mutex for regulators locking") Fixes: e915331 ("regulator: vctrl-regulator: Avoid deadlock getting and setting the voltage") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Link: https://lore.kernel.org/r/20210825033704.3307263-3-wenst@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 13be2ef upstream. As previously noted in commit 66e4f4a ("rtc: cmos: Use spin_lock_irqsave() in cmos_interrupt()"): <4>[ 254.192378] WARNING: inconsistent lock state <4>[ 254.192384] 5.12.0-rc1-CI-CI_DRM_9834+ #1 Not tainted <4>[ 254.192396] -------------------------------- <4>[ 254.192400] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage. <4>[ 254.192409] rtcwake/5309 [HC0[0]:SC0[0]:HE1:SE1] takes: <4>[ 254.192429] ffffffff8263c5f8 (rtc_lock){?...}-{2:2}, at: cmos_interrupt+0x18/0x100 <4>[ 254.192481] {IN-HARDIRQ-W} state was registered at: <4>[ 254.192488] lock_acquire+0xd1/0x3d0 <4>[ 254.192504] _raw_spin_lock+0x2a/0x40 <4>[ 254.192519] cmos_interrupt+0x18/0x100 <4>[ 254.192536] rtc_handler+0x1f/0xc0 <4>[ 254.192553] acpi_ev_fixed_event_detect+0x109/0x13c <4>[ 254.192574] acpi_ev_sci_xrupt_handler+0xb/0x28 <4>[ 254.192596] acpi_irq+0x13/0x30 <4>[ 254.192620] __handle_irq_event_percpu+0x43/0x2c0 <4>[ 254.192641] handle_irq_event_percpu+0x2b/0x70 <4>[ 254.192661] handle_irq_event+0x2f/0x50 <4>[ 254.192680] handle_fasteoi_irq+0x9e/0x150 <4>[ 254.192693] __common_interrupt+0x76/0x140 <4>[ 254.192715] common_interrupt+0x96/0xc0 <4>[ 254.192732] asm_common_interrupt+0x1e/0x40 <4>[ 254.192750] _raw_spin_unlock_irqrestore+0x38/0x60 <4>[ 254.192767] resume_irqs+0xba/0xf0 <4>[ 254.192786] dpm_resume_noirq+0x245/0x3d0 <4>[ 254.192811] suspend_devices_and_enter+0x230/0xaa0 <4>[ 254.192835] pm_suspend.cold.8+0x301/0x34a <4>[ 254.192859] state_store+0x7b/0xe0 <4>[ 254.192879] kernfs_fop_write_iter+0x11d/0x1c0 <4>[ 254.192899] new_sync_write+0x11d/0x1b0 <4>[ 254.192916] vfs_write+0x265/0x390 <4>[ 254.192933] ksys_write+0x5a/0xd0 <4>[ 254.192949] do_syscall_64+0x33/0x80 <4>[ 254.192965] entry_SYSCALL_64_after_hwframe+0x44/0xae <4>[ 254.192986] irq event stamp: 43775 <4>[ 254.192994] hardirqs last enabled at (43775): [<ffffffff81c00c42>] asm_sysvec_apic_timer_interrupt+0x12/0x20 <4>[ 254.193023] hardirqs last disabled at (43774): [<ffffffff81aa691a>] sysvec_apic_timer_interrupt+0xa/0xb0 <4>[ 254.193049] softirqs last enabled at (42548): [<ffffffff81e00342>] __do_softirq+0x342/0x48e <4>[ 254.193074] softirqs last disabled at (42543): [<ffffffff810b45fd>] irq_exit_rcu+0xad/0xd0 <4>[ 254.193101] other info that might help us debug this: <4>[ 254.193107] Possible unsafe locking scenario: <4>[ 254.193112] CPU0 <4>[ 254.193117] ---- <4>[ 254.193121] lock(rtc_lock); <4>[ 254.193137] <Interrupt> <4>[ 254.193142] lock(rtc_lock); <4>[ 254.193156] *** DEADLOCK *** <4>[ 254.193161] 6 locks held by rtcwake/5309: <4>[ 254.193174] #0: ffff888104861430 (sb_writers#5){.+.+}-{0:0}, at: ksys_write+0x5a/0xd0 <4>[ 254.193232] #1: ffff88810f823288 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0xe7/0x1c0 <4>[ 254.193282] #2: ffff888100cef3c0 (kn->active#285 <7>[ 254.192706] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <4>[ 254.193307] ){.+.+}-{0:0}, at: kernfs_fop_write_iter+0xf0/0x1c0 <4>[ 254.193333] #3: ffffffff82649fa8 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend.cold.8+0xce/0x34a <4>[ 254.193387] #4: ffffffff827a2108 (acpi_scan_lock){+.+.}-{3:3}, at: acpi_suspend_begin+0x47/0x70 <4>[ 254.193433] #5: ffff8881019ea178 (&dev->mutex){....}-{3:3}, at: device_resume+0x68/0x1e0 <4>[ 254.193485] stack backtrace: <4>[ 254.193492] CPU: 1 PID: 5309 Comm: rtcwake Not tainted 5.12.0-rc1-CI-CI_DRM_9834+ #1 <4>[ 254.193514] Hardware name: Google Soraka/Soraka, BIOS MrChromebox-4.10 08/25/2019 <4>[ 254.193524] Call Trace: <4>[ 254.193536] dump_stack+0x7f/0xad <4>[ 254.193567] mark_lock.part.47+0x8ca/0xce0 <4>[ 254.193604] __lock_acquire+0x39b/0x2590 <4>[ 254.193626] ? asm_sysvec_apic_timer_interrupt+0x12/0x20 <4>[ 254.193660] lock_acquire+0xd1/0x3d0 <4>[ 254.193677] ? cmos_interrupt+0x18/0x100 <4>[ 254.193716] _raw_spin_lock+0x2a/0x40 <4>[ 254.193735] ? cmos_interrupt+0x18/0x100 <4>[ 254.193758] cmos_interrupt+0x18/0x100 <4>[ 254.193785] cmos_resume+0x2ac/0x2d0 <4>[ 254.193813] ? acpi_pm_set_device_wakeup+0x1f/0x110 <4>[ 254.193842] ? pnp_bus_suspend+0x10/0x10 <4>[ 254.193864] pnp_bus_resume+0x5e/0x90 <4>[ 254.193885] dpm_run_callback+0x5f/0x240 <4>[ 254.193914] device_resume+0xb2/0x1e0 <4>[ 254.193942] ? pm_dev_err+0x25/0x25 <4>[ 254.193974] dpm_resume+0xea/0x3f0 <4>[ 254.194005] dpm_resume_end+0x8/0x10 <4>[ 254.194030] suspend_devices_and_enter+0x29b/0xaa0 <4>[ 254.194066] pm_suspend.cold.8+0x301/0x34a <4>[ 254.194094] state_store+0x7b/0xe0 <4>[ 254.194124] kernfs_fop_write_iter+0x11d/0x1c0 <4>[ 254.194151] new_sync_write+0x11d/0x1b0 <4>[ 254.194183] vfs_write+0x265/0x390 <4>[ 254.194207] ksys_write+0x5a/0xd0 <4>[ 254.194232] do_syscall_64+0x33/0x80 <4>[ 254.194251] entry_SYSCALL_64_after_hwframe+0x44/0xae <4>[ 254.194274] RIP: 0033:0x7f07d79691e7 <4>[ 254.194293] Code: 64 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24 <4>[ 254.194312] RSP: 002b:00007ffd9cc2c768 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 <4>[ 254.194337] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007f07d79691e7 <4>[ 254.194352] RDX: 0000000000000004 RSI: 0000556ebfc63590 RDI: 000000000000000b <4>[ 254.194366] RBP: 0000556ebfc63590 R08: 0000000000000000 R09: 0000000000000004 <4>[ 254.194379] R10: 0000556ebf0ec2a6 R11: 0000000000000246 R12: 0000000000000004 which breaks S3-resume on fi-kbl-soraka presumably as that's slow enough to trigger the alarm during the suspend. Fixes: 6950d04 ("rtc: cmos: Replace spin_lock_irqsave with spin_lock in hard IRQ") References: 66e4f4a ("rtc: cmos: Use spin_lock_irqsave() in cmos_interrupt()"): Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Xiaofei Tan <tanxiaofei@huawei.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20210305122140.28774-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 57f0ff0 upstream. It's later supposed to be either a correct address or NULL. Without the initialization, it may contain an undefined value which results in the following segmentation fault: # perf top --sort comm -g --ignore-callees=do_idle terminates with: #0 0x00007ffff56b7685 in __strlen_avx2 () from /lib64/libc.so.6 #1 0x00007ffff55e3802 in strdup () from /lib64/libc.so.6 #2 0x00005555558cb139 in hist_entry__init (callchain_size=<optimized out>, sample_self=true, template=0x7fffde7fb110, he=0x7fffd801c250) at util/hist.c:489 #3 hist_entry__new (template=template@entry=0x7fffde7fb110, sample_self=sample_self@entry=true) at util/hist.c:564 #4 0x00005555558cb4ba in hists__findnew_entry (hists=hists@entry=0x5555561d9e38, entry=entry@entry=0x7fffde7fb110, al=al@entry=0x7fffde7fb420, sample_self=sample_self@entry=true) at util/hist.c:657 #5 0x00005555558cba1b in __hists__add_entry (hists=hists@entry=0x5555561d9e38, al=0x7fffde7fb420, sym_parent=<optimized out>, bi=bi@entry=0x0, mi=mi@entry=0x0, sample=sample@entry=0x7fffde7fb4b0, sample_self=true, ops=0x0, block_info=0x0) at util/hist.c:288 gregkh#6 0x00005555558cbb70 in hists__add_entry (sample_self=true, sample=0x7fffde7fb4b0, mi=0x0, bi=0x0, sym_parent=<optimized out>, al=<optimized out>, hists=0x5555561d9e38) at util/hist.c:1056 gregkh#7 iter_add_single_cumulative_entry (iter=0x7fffde7fb460, al=<optimized out>) at util/hist.c:1056 gregkh#8 0x00005555558cc8a4 in hist_entry_iter__add (iter=iter@entry=0x7fffde7fb460, al=al@entry=0x7fffde7fb420, max_stack_depth=<optimized out>, arg=arg@entry=0x7fffffff7db0) at util/hist.c:1231 gregkh#9 0x00005555557cdc9a in perf_event__process_sample (machine=<optimized out>, sample=0x7fffde7fb4b0, evsel=<optimized out>, event=<optimized out>, tool=0x7fffffff7db0) at builtin-top.c:842 gregkh#10 deliver_event (qe=<optimized out>, qevent=<optimized out>) at builtin-top.c:1202 gregkh#11 0x00005555558a9318 in do_flush (show_progress=false, oe=0x7fffffff80e0) at util/ordered-events.c:244 gregkh#12 __ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP, timestamp=timestamp@entry=0) at util/ordered-events.c:323 gregkh#13 0x00005555558a9789 in __ordered_events__flush (timestamp=<optimized out>, how=<optimized out>, oe=<optimized out>) at util/ordered-events.c:339 gregkh#14 ordered_events__flush (how=OE_FLUSH__TOP, oe=0x7fffffff80e0) at util/ordered-events.c:341 gregkh#15 ordered_events__flush (oe=oe@entry=0x7fffffff80e0, how=how@entry=OE_FLUSH__TOP) at util/ordered-events.c:339 gregkh#16 0x00005555557cd631 in process_thread (arg=0x7fffffff7db0) at builtin-top.c:1114 gregkh#17 0x00007ffff7bb817a in start_thread () from /lib64/libpthread.so.0 gregkh#18 0x00007ffff5656dc3 in clone () from /lib64/libc.so.6 If you look at the frame #2, the code is: 488 if (he->srcline) { 489 he->srcline = strdup(he->srcline); 490 if (he->srcline == NULL) 491 goto err_rawdata; 492 } If he->srcline is not NULL (it is not NULL if it is uninitialized rubbish), it gets strdupped and strdupping a rubbish random string causes the problem. Also, if you look at the commit 1fb7d06, it adds the srcline property into the struct, but not initializing it everywhere needed. Committer notes: Now I see, when using --ignore-callees=do_idle we end up here at line 2189 in add_callchain_ip(): 2181 if (al.sym != NULL) { 2182 if (perf_hpp_list.parent && !*parent && 2183 symbol__match_regex(al.sym, &parent_regex)) 2184 *parent = al.sym; 2185 else if (have_ignore_callees && root_al && 2186 symbol__match_regex(al.sym, &ignore_callees_regex)) { 2187 /* Treat this symbol as the root, 2188 forgetting its callees. */ 2189 *root_al = al; 2190 callchain_cursor_reset(cursor); 2191 } 2192 } And the al that doesn't have the ->srcline field initialized will be copied to the root_al, so then, back to: 1211 int hist_entry_iter__add(struct hist_entry_iter *iter, struct addr_location *al, 1212 int max_stack_depth, void *arg) 1213 { 1214 int err, err2; 1215 struct map *alm = NULL; 1216 1217 if (al) 1218 alm = map__get(al->map); 1219 1220 err = sample__resolve_callchain(iter->sample, &callchain_cursor, &iter->parent, 1221 iter->evsel, al, max_stack_depth); 1222 if (err) { 1223 map__put(alm); 1224 return err; 1225 } 1226 1227 err = iter->ops->prepare_entry(iter, al); 1228 if (err) 1229 goto out; 1230 1231 err = iter->ops->add_single_entry(iter, al); 1232 if (err) 1233 goto out; 1234 That al at line 1221 is what hist_entry_iter__add() (called from sample__resolve_callchain()) saw as 'root_al', and then: iter->ops->add_single_entry(iter, al); will go on with al->srcline with a bogus value, I'll add the above sequence to the cset and apply, thanks! Signed-off-by: Michael Petlan <mpetlan@redhat.com> CC: Milian Wolff <milian.wolff@kdab.com> Cc: Jiri Olsa <jolsa@redhat.com> Fixes: 1fb7d06 ("perf report Use srcline from callchain for hist entries") Link: https //lore.kernel.org/r/20210719145332.29747-1-mpetlan@redhat.com Reported-by: Juri Lelli <jlelli@redhat.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8f96a5b ] We update the ctime/mtime of a block device when we remove it so that blkid knows the device changed. However we do this by re-opening the block device and calling filp_update_time. This is more correct because it'll call the inode->i_op->update_time if it exists, but the block dev inodes do not do this. Instead call generic_update_time() on the bd_inode in order to avoid the blkdev_open path and get rid of the following lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.14.0-rc2+ #406 Not tainted ------------------------------------------------------ losetup/11596 is trying to acquire lock: ffff939640d2f538 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x67/0x5e0 but task is already holding lock: ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> gregkh#4 (&lo->lo_mutex){+.+.}-{3:3}: __mutex_lock+0x7d/0x750 lo_open+0x28/0x60 [loop] blkdev_get_whole+0x25/0xf0 blkdev_get_by_dev.part.0+0x168/0x3c0 blkdev_open+0xd2/0xe0 do_dentry_open+0x161/0x390 path_openat+0x3cc/0xa20 do_filp_open+0x96/0x120 do_sys_openat2+0x7b/0x130 __x64_sys_openat+0x46/0x70 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#3 (&disk->open_mutex){+.+.}-{3:3}: __mutex_lock+0x7d/0x750 blkdev_get_by_dev.part.0+0x56/0x3c0 blkdev_open+0xd2/0xe0 do_dentry_open+0x161/0x390 path_openat+0x3cc/0xa20 do_filp_open+0x96/0x120 file_open_name+0xc7/0x170 filp_open+0x2c/0x50 btrfs_scratch_superblocks.part.0+0x10f/0x170 btrfs_rm_device.cold+0xe8/0xed btrfs_ioctl+0x2a31/0x2e70 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#2 (sb_writers#12){.+.+}-{0:0}: lo_write_bvec+0xc2/0x240 [loop] loop_process_work+0x238/0xd00 [loop] process_one_work+0x26b/0x560 worker_thread+0x55/0x3c0 kthread+0x140/0x160 ret_from_fork+0x1f/0x30 -> gregkh#1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}: process_one_work+0x245/0x560 worker_thread+0x55/0x3c0 kthread+0x140/0x160 ret_from_fork+0x1f/0x30 -> #0 ((wq_completion)loop0){+.+.}-{0:0}: __lock_acquire+0x10ea/0x1d90 lock_acquire+0xb5/0x2b0 flush_workqueue+0x91/0x5e0 drain_workqueue+0xa0/0x110 destroy_workqueue+0x36/0x250 __loop_clr_fd+0x9a/0x660 [loop] block_ioctl+0x3f/0x50 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae other info that might help us debug this: Chain exists of: (wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&lo->lo_mutex); lock(&disk->open_mutex); lock(&lo->lo_mutex); lock((wq_completion)loop0); *** DEADLOCK *** 1 lock held by losetup/11596: #0: ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop] stack backtrace: CPU: 1 PID: 11596 Comm: losetup Not tainted 5.14.0-rc2+ #406 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014 Call Trace: dump_stack_lvl+0x57/0x72 check_noncircular+0xcf/0xf0 ? stack_trace_save+0x3b/0x50 __lock_acquire+0x10ea/0x1d90 lock_acquire+0xb5/0x2b0 ? flush_workqueue+0x67/0x5e0 ? lockdep_init_map_type+0x47/0x220 flush_workqueue+0x91/0x5e0 ? flush_workqueue+0x67/0x5e0 ? verify_cpu+0xf0/0x100 drain_workqueue+0xa0/0x110 destroy_workqueue+0x36/0x250 __loop_clr_fd+0x9a/0x660 [loop] ? blkdev_ioctl+0x8d/0x2a0 block_ioctl+0x3f/0x50 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3fa421d ] When removing the device we call blkdev_put() on the device once we've removed it, and because we have an EXCL open we need to take the ->open_mutex on the block device to clean it up. Unfortunately during device remove we are holding the sb writers lock, which results in the following lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.14.0-rc2+ #407 Not tainted ------------------------------------------------------ losetup/11595 is trying to acquire lock: ffff973ac35dd138 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x67/0x5e0 but task is already holding lock: ffff973ac9812c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> gregkh#4 (&lo->lo_mutex){+.+.}-{3:3}: __mutex_lock+0x7d/0x750 lo_open+0x28/0x60 [loop] blkdev_get_whole+0x25/0xf0 blkdev_get_by_dev.part.0+0x168/0x3c0 blkdev_open+0xd2/0xe0 do_dentry_open+0x161/0x390 path_openat+0x3cc/0xa20 do_filp_open+0x96/0x120 do_sys_openat2+0x7b/0x130 __x64_sys_openat+0x46/0x70 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#3 (&disk->open_mutex){+.+.}-{3:3}: __mutex_lock+0x7d/0x750 blkdev_put+0x3a/0x220 btrfs_rm_device.cold+0x62/0xe5 btrfs_ioctl+0x2a31/0x2e70 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#2 (sb_writers#12){.+.+}-{0:0}: lo_write_bvec+0xc2/0x240 [loop] loop_process_work+0x238/0xd00 [loop] process_one_work+0x26b/0x560 worker_thread+0x55/0x3c0 kthread+0x140/0x160 ret_from_fork+0x1f/0x30 -> gregkh#1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}: process_one_work+0x245/0x560 worker_thread+0x55/0x3c0 kthread+0x140/0x160 ret_from_fork+0x1f/0x30 -> #0 ((wq_completion)loop0){+.+.}-{0:0}: __lock_acquire+0x10ea/0x1d90 lock_acquire+0xb5/0x2b0 flush_workqueue+0x91/0x5e0 drain_workqueue+0xa0/0x110 destroy_workqueue+0x36/0x250 __loop_clr_fd+0x9a/0x660 [loop] block_ioctl+0x3f/0x50 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae other info that might help us debug this: Chain exists of: (wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&lo->lo_mutex); lock(&disk->open_mutex); lock(&lo->lo_mutex); lock((wq_completion)loop0); *** DEADLOCK *** 1 lock held by losetup/11595: #0: ffff973ac9812c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop] stack backtrace: CPU: 0 PID: 11595 Comm: losetup Not tainted 5.14.0-rc2+ #407 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014 Call Trace: dump_stack_lvl+0x57/0x72 check_noncircular+0xcf/0xf0 ? stack_trace_save+0x3b/0x50 __lock_acquire+0x10ea/0x1d90 lock_acquire+0xb5/0x2b0 ? flush_workqueue+0x67/0x5e0 ? lockdep_init_map_type+0x47/0x220 flush_workqueue+0x91/0x5e0 ? flush_workqueue+0x67/0x5e0 ? verify_cpu+0xf0/0x100 drain_workqueue+0xa0/0x110 destroy_workqueue+0x36/0x250 __loop_clr_fd+0x9a/0x660 [loop] ? blkdev_ioctl+0x8d/0x2a0 block_ioctl+0x3f/0x50 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7fc21255d4cb So instead save the bdev and do the put once we've dropped the sb writers lock in order to avoid the lockdep recursion. Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit dfbb340 ] If CONFIG_BLK_DEV_LOOP && CONFIG_MTD (at least; there might be other combinations), lockdep complains circular locking dependency at __loop_clr_fd(), for major_names_lock serves as a locking dependency aggregating hub across multiple block modules. ====================================================== WARNING: possible circular locking dependency detected 5.14.0+ #757 Tainted: G E ------------------------------------------------------ systemd-udevd/7568 is trying to acquire lock: ffff88800f334d48 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x70/0x560 but task is already holding lock: ffff888014a7d4a0 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x4d/0x400 [loop] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> gregkh#6 (&lo->lo_mutex){+.+.}-{3:3}: lock_acquire+0xbe/0x1f0 __mutex_lock_common+0xb6/0xe10 mutex_lock_killable_nested+0x17/0x20 lo_open+0x23/0x50 [loop] blkdev_get_by_dev+0x199/0x540 blkdev_open+0x58/0x90 do_dentry_open+0x144/0x3a0 path_openat+0xa57/0xda0 do_filp_open+0x9f/0x140 do_sys_openat2+0x71/0x150 __x64_sys_openat+0x78/0xa0 do_syscall_64+0x3d/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#5 (&disk->open_mutex){+.+.}-{3:3}: lock_acquire+0xbe/0x1f0 __mutex_lock_common+0xb6/0xe10 mutex_lock_nested+0x17/0x20 bd_register_pending_holders+0x20/0x100 device_add_disk+0x1ae/0x390 loop_add+0x29c/0x2d0 [loop] blk_request_module+0x5a/0xb0 blkdev_get_no_open+0x27/0xa0 blkdev_get_by_dev+0x5f/0x540 blkdev_open+0x58/0x90 do_dentry_open+0x144/0x3a0 path_openat+0xa57/0xda0 do_filp_open+0x9f/0x140 do_sys_openat2+0x71/0x150 __x64_sys_openat+0x78/0xa0 do_syscall_64+0x3d/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#4 (major_names_lock){+.+.}-{3:3}: lock_acquire+0xbe/0x1f0 __mutex_lock_common+0xb6/0xe10 mutex_lock_nested+0x17/0x20 blkdev_show+0x19/0x80 devinfo_show+0x52/0x60 seq_read_iter+0x2d5/0x3e0 proc_reg_read_iter+0x41/0x80 vfs_read+0x2ac/0x330 ksys_read+0x6b/0xd0 do_syscall_64+0x3d/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#3 (&p->lock){+.+.}-{3:3}: lock_acquire+0xbe/0x1f0 __mutex_lock_common+0xb6/0xe10 mutex_lock_nested+0x17/0x20 seq_read_iter+0x37/0x3e0 generic_file_splice_read+0xf3/0x170 splice_direct_to_actor+0x14e/0x350 do_splice_direct+0x84/0xd0 do_sendfile+0x263/0x430 __se_sys_sendfile64+0x96/0xc0 do_syscall_64+0x3d/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#2 (sb_writers#3){.+.+}-{0:0}: lock_acquire+0xbe/0x1f0 lo_write_bvec+0x96/0x280 [loop] loop_process_work+0xa68/0xc10 [loop] process_one_work+0x293/0x480 worker_thread+0x23d/0x4b0 kthread+0x163/0x180 ret_from_fork+0x1f/0x30 -> gregkh#1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}: lock_acquire+0xbe/0x1f0 process_one_work+0x280/0x480 worker_thread+0x23d/0x4b0 kthread+0x163/0x180 ret_from_fork+0x1f/0x30 -> #0 ((wq_completion)loop0){+.+.}-{0:0}: validate_chain+0x1f0d/0x33e0 __lock_acquire+0x92d/0x1030 lock_acquire+0xbe/0x1f0 flush_workqueue+0x8c/0x560 drain_workqueue+0x80/0x140 destroy_workqueue+0x47/0x4f0 __loop_clr_fd+0xb4/0x400 [loop] blkdev_put+0x14a/0x1d0 blkdev_close+0x1c/0x20 __fput+0xfd/0x220 task_work_run+0x69/0xc0 exit_to_user_mode_prepare+0x1ce/0x1f0 syscall_exit_to_user_mode+0x26/0x60 do_syscall_64+0x4c/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae other info that might help us debug this: Chain exists of: (wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&lo->lo_mutex); lock(&disk->open_mutex); lock(&lo->lo_mutex); lock((wq_completion)loop0); *** DEADLOCK *** 2 locks held by systemd-udevd/7568: #0: ffff888012554128 (&disk->open_mutex){+.+.}-{3:3}, at: blkdev_put+0x4c/0x1d0 gregkh#1: ffff888014a7d4a0 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x4d/0x400 [loop] stack backtrace: CPU: 0 PID: 7568 Comm: systemd-udevd Tainted: G E 5.14.0+ #757 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 02/27/2020 Call Trace: dump_stack_lvl+0x79/0xbf print_circular_bug+0x5d6/0x5e0 ? stack_trace_save+0x42/0x60 ? save_trace+0x3d/0x2d0 check_noncircular+0x10b/0x120 validate_chain+0x1f0d/0x33e0 ? __lock_acquire+0x953/0x1030 ? __lock_acquire+0x953/0x1030 __lock_acquire+0x92d/0x1030 ? flush_workqueue+0x70/0x560 lock_acquire+0xbe/0x1f0 ? flush_workqueue+0x70/0x560 flush_workqueue+0x8c/0x560 ? flush_workqueue+0x70/0x560 ? sched_clock_cpu+0xe/0x1a0 ? drain_workqueue+0x41/0x140 drain_workqueue+0x80/0x140 destroy_workqueue+0x47/0x4f0 ? blk_mq_freeze_queue_wait+0xac/0xd0 __loop_clr_fd+0xb4/0x400 [loop] ? __mutex_unlock_slowpath+0x35/0x230 blkdev_put+0x14a/0x1d0 blkdev_close+0x1c/0x20 __fput+0xfd/0x220 task_work_run+0x69/0xc0 exit_to_user_mode_prepare+0x1ce/0x1f0 syscall_exit_to_user_mode+0x26/0x60 do_syscall_64+0x4c/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f0fd4c661f7 Code: 00 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 41 c3 48 83 ec 18 89 7c 24 0c e8 13 fc ff ff RSP: 002b:00007ffd1c9e9fd8 EFLAGS: 00000246 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 00007f0fd46be6c8 RCX: 00007f0fd4c661f7 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000006 RBP: 0000000000000006 R08: 000055fff1eaf400 R09: 0000000000000000 R10: 00007f0fd46be6c8 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000002f08 R15: 00007ffd1c9ea050 Commit 1c500ad ("loop: reduce the loop_ctl_mutex scope") is for breaking "loop_ctl_mutex => &lo->lo_mutex" dependency chain. But enabling a different block module results in forming circular locking dependency due to shared major_names_lock mutex. The simplest fix is to call probe function without holding major_names_lock [1], but Christoph Hellwig does not like such idea. Therefore, instead of holding major_names_lock in blkdev_show(), introduce a different lock for blkdev_show() in order to break "sb_writers#$N => &p->lock => major_names_lock" dependency chain. Link: https://lkml.kernel.org/r/b2af8a5b-3c1b-204e-7f56-bea0b15848d6@i-love.sakura.ne.jp [1] Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/18a02da2-0bf3-550e-b071-2b4ab13c49f0@i-love.sakura.ne.jp Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8f96a5b ] We update the ctime/mtime of a block device when we remove it so that blkid knows the device changed. However we do this by re-opening the block device and calling filp_update_time. This is more correct because it'll call the inode->i_op->update_time if it exists, but the block dev inodes do not do this. Instead call generic_update_time() on the bd_inode in order to avoid the blkdev_open path and get rid of the following lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.14.0-rc2+ #406 Not tainted ------------------------------------------------------ losetup/11596 is trying to acquire lock: ffff939640d2f538 ((wq_completion)loop0){+.+.}-{0:0}, at: flush_workqueue+0x67/0x5e0 but task is already holding lock: ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> gregkh#4 (&lo->lo_mutex){+.+.}-{3:3}: __mutex_lock+0x7d/0x750 lo_open+0x28/0x60 [loop] blkdev_get_whole+0x25/0xf0 blkdev_get_by_dev.part.0+0x168/0x3c0 blkdev_open+0xd2/0xe0 do_dentry_open+0x161/0x390 path_openat+0x3cc/0xa20 do_filp_open+0x96/0x120 do_sys_openat2+0x7b/0x130 __x64_sys_openat+0x46/0x70 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#3 (&disk->open_mutex){+.+.}-{3:3}: __mutex_lock+0x7d/0x750 blkdev_get_by_dev.part.0+0x56/0x3c0 blkdev_open+0xd2/0xe0 do_dentry_open+0x161/0x390 path_openat+0x3cc/0xa20 do_filp_open+0x96/0x120 file_open_name+0xc7/0x170 filp_open+0x2c/0x50 btrfs_scratch_superblocks.part.0+0x10f/0x170 btrfs_rm_device.cold+0xe8/0xed btrfs_ioctl+0x2a31/0x2e70 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae -> gregkh#2 (sb_writers#12){.+.+}-{0:0}: lo_write_bvec+0xc2/0x240 [loop] loop_process_work+0x238/0xd00 [loop] process_one_work+0x26b/0x560 worker_thread+0x55/0x3c0 kthread+0x140/0x160 ret_from_fork+0x1f/0x30 -> gregkh#1 ((work_completion)(&lo->rootcg_work)){+.+.}-{0:0}: process_one_work+0x245/0x560 worker_thread+0x55/0x3c0 kthread+0x140/0x160 ret_from_fork+0x1f/0x30 -> #0 ((wq_completion)loop0){+.+.}-{0:0}: __lock_acquire+0x10ea/0x1d90 lock_acquire+0xb5/0x2b0 flush_workqueue+0x91/0x5e0 drain_workqueue+0xa0/0x110 destroy_workqueue+0x36/0x250 __loop_clr_fd+0x9a/0x660 [loop] block_ioctl+0x3f/0x50 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae other info that might help us debug this: Chain exists of: (wq_completion)loop0 --> &disk->open_mutex --> &lo->lo_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&lo->lo_mutex); lock(&disk->open_mutex); lock(&lo->lo_mutex); lock((wq_completion)loop0); *** DEADLOCK *** 1 lock held by losetup/11596: #0: ffff939655510c68 (&lo->lo_mutex){+.+.}-{3:3}, at: __loop_clr_fd+0x41/0x660 [loop] stack backtrace: CPU: 1 PID: 11596 Comm: losetup Not tainted 5.14.0-rc2+ #406 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014 Call Trace: dump_stack_lvl+0x57/0x72 check_noncircular+0xcf/0xf0 ? stack_trace_save+0x3b/0x50 __lock_acquire+0x10ea/0x1d90 lock_acquire+0xb5/0x2b0 ? flush_workqueue+0x67/0x5e0 ? lockdep_init_map_type+0x47/0x220 flush_workqueue+0x91/0x5e0 ? flush_workqueue+0x67/0x5e0 ? verify_cpu+0xf0/0x100 drain_workqueue+0xa0/0x110 destroy_workqueue+0x36/0x250 __loop_clr_fd+0x9a/0x660 [loop] ? blkdev_ioctl+0x8d/0x2a0 block_ioctl+0x3f/0x50 __x64_sys_ioctl+0x80/0xb0 do_syscall_64+0x38/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit aba5dae ] FD uses xyarray__entry that may return NULL if an index is out of bounds. If NULL is returned then a segv happens as FD unconditionally dereferences the pointer. This was happening in a case of with perf iostat as shown below. The fix is to make FD an "int*" rather than an int and handle the NULL case as either invalid input or a closed fd. $ sudo gdb --args perf stat --iostat list ... Breakpoint 1, perf_evsel__alloc_fd (evsel=0x5555560951a0, ncpus=1, nthreads=1) at evsel.c:50 50 { (gdb) bt #0 perf_evsel__alloc_fd (evsel=0x5555560951a0, ncpus=1, nthreads=1) at evsel.c:50 #1 0x000055555585c188 in evsel__open_cpu (evsel=0x5555560951a0, cpus=0x555556093410, threads=0x555556086fb0, start_cpu=0, end_cpu=1) at util/evsel.c:1792 #2 0x000055555585cfb2 in evsel__open (evsel=0x5555560951a0, cpus=0x0, threads=0x555556086fb0) at util/evsel.c:2045 #3 0x000055555585d0db in evsel__open_per_thread (evsel=0x5555560951a0, threads=0x555556086fb0) at util/evsel.c:2065 #4 0x00005555558ece64 in create_perf_stat_counter (evsel=0x5555560951a0, config=0x555555c34700 <stat_config>, target=0x555555c2f1c0 <target>, cpu=0) at util/stat.c:590 #5 0x000055555578e927 in __run_perf_stat (argc=1, argv=0x7fffffffe4a0, run_idx=0) at builtin-stat.c:833 gregkh#6 0x000055555578f3c6 in run_perf_stat (argc=1, argv=0x7fffffffe4a0, run_idx=0) at builtin-stat.c:1048 gregkh#7 0x0000555555792ee5 in cmd_stat (argc=1, argv=0x7fffffffe4a0) at builtin-stat.c:2534 gregkh#8 0x0000555555835ed3 in run_builtin (p=0x555555c3f540 <commands+288>, argc=3, argv=0x7fffffffe4a0) at perf.c:313 gregkh#9 0x0000555555836154 in handle_internal_command (argc=3, argv=0x7fffffffe4a0) at perf.c:365 gregkh#10 0x000055555583629f in run_argv (argcp=0x7fffffffe2ec, argv=0x7fffffffe2e0) at perf.c:409 gregkh#11 0x0000555555836692 in main (argc=3, argv=0x7fffffffe4a0) at perf.c:539 ... (gdb) c Continuing. Error: The sys_perf_event_open() syscall returned with 22 (Invalid argument) for event (uncore_iio_0/event=0x83,umask=0x04,ch_mask=0xF,fc_mask=0x07/). /bin/dmesg | grep -i perf may provide additional information. Program received signal SIGSEGV, Segmentation fault. 0x00005555559b03ea in perf_evsel__close_fd_cpu (evsel=0x5555560951a0, cpu=1) at evsel.c:166 166 if (FD(evsel, cpu, thread) >= 0) v3. fixes a bug in perf_evsel__run_ioctl where the sense of a branch was backward. Signed-off-by: Ian Rogers <irogers@google.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20210918054440.2350466-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

Pablo Neira Ayuso says: ==================== Netfilter fixes for net (v2) The following patchset contains Netfilter fixes for net: 1) Move back the defrag users fields to the global netns_nf area. Kernel fails to boot if conntrack is builtin and kernel is booted with: nf_conntrack.enable_hooks=1. From Florian Westphal. 2) Rule event notification is missing relevant context such as the position handle and the NLM_F_APPEND flag. 3) Rule replacement is expanded to add + delete using the existing rule handle, reverse order of this operation so it makes sense from rule notification standpoint. 4) Propagate to userspace the NLM_F_CREATE and NLM_F_EXCL flags from the rule notification path. Patches gregkh#2, gregkh#3 and gregkh#4 are used by 'nft monitor' and 'iptables-monitor' userspace utilities which are not correctly representing the following operations through netlink notifications: - rule insertions - rule addition/insertion from position handle - create table/chain/set/map/flowtable/... ==================== Signed-off-by: David S. Miller <davem@davemloft.net>

[ Upstream commit 2c48441 ] lz4 compatible decompressor is simple. The format is underspecified and relies on EOF notification to determine when to stop. Initramfs buffer format[1] explicitly states that it can have arbitrary number of zero padding. Thus when operating without a fill function, be extra careful to ensure that sizes less than 4, or apperantly empty chunksizes are treated as EOF. To test this I have created two cpio initrds, first a normal one, main.cpio. And second one with just a single /test-file with content "second" second.cpio. Then i compressed both of them with gzip, and with lz4 -l. Then I created a padding of 4 bytes (dd if=/dev/zero of=pad4 bs=1 count=4). To create four testcase initrds: 1) main.cpio.gzip + extra.cpio.gzip = pad0.gzip 2) main.cpio.lz4 + extra.cpio.lz4 = pad0.lz4 3) main.cpio.gzip + pad4 + extra.cpio.gzip = pad4.gzip 4) main.cpio.lz4 + pad4 + extra.cpio.lz4 = pad4.lz4 The pad4 test-cases replicate the initrd load by grub, as it pads and aligns every initrd it loads. All of the above boot, however /test-file was not accessible in the initrd for the testcase gregkh#4, as decoding in lz4 decompressor failed. Also an error message printed which usually is harmless. Whith a patched kernel, all of the above testcases now pass, and /test-file is accessible. This fixes lz4 initrd decompress warning on every boot with grub. And more importantly this fixes inability to load multiple lz4 compressed initrds with grub. This patch has been shipping in Ubuntu kernels since January 2021. [1] ./Documentation/driver-api/early-userspace/buffer-format.rst BugLink: https://bugs.launchpad.net/bugs/1835660 Link: https://lore.kernel.org/lkml/20210114200256.196589-1-xnox@ubuntu.com/ # v0 Link: https://lkml.kernel.org/r/20210513104831.432975-1-dimitri.ledkov@canonical.com Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com> Cc: Kyungsik Lee <kyungsik.lee@lge.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Bongkyu Kim <bongkyu.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Sven Schmidt <4sschmid@informatik.uni-hamburg.de> Cc: Rajat Asthana <thisisrast7@gmail.com> Cc: Nick Terrell <terrelln@fb.com> Cc: Gao Xiang <hsiangkao@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 4385539 upstream. The ordering of MSI-X enable in hardware is dysfunctional: 1) MSI-X is disabled in the control register 2) Various setup functions 3) pci_msi_setup_msi_irqs() is invoked which ends up accessing the MSI-X table entries 4) MSI-X is enabled and masked in the control register with the comment that enabling is required for some hardware to access the MSI-X table Step gregkh#4 obviously contradicts gregkh#3. The history of this is an issue with the NIU hardware. When gregkh#4 was introduced the table access actually happened in msix_program_entries() which was invoked after enabling and masking MSI-X. This was changed in commit d71d643 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") which removed the table write from msix_program_entries(). Interestingly enough nobody noticed and either NIU still works or it did not get any testing with a kernel 3.19 or later. Nevertheless this is inconsistent and there is no reason why MSI-X can't be enabled and masked in the control register early on, i.e. move step gregkh#4 above to step gregkh#1. This preserves the NIU workaround and has no side effects on other hardware. Fixes: d71d643 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 376565b upstream. KMSAN complains that the vmci_use_ppn64() == false path in vmci_dbell_register_notification_bitmap() left upper 32bits of bitmap_set_msg.bitmap_ppn64 member uninitialized. ===================================================== BUG: KMSAN: uninit-value in kmsan_check_memory+0xd/0x10 CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.11.0-rc7+ gregkh#4 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 02/27/2020 Call Trace: dump_stack+0x21c/0x280 kmsan_report+0xfb/0x1e0 kmsan_internal_check_memory+0x484/0x520 kmsan_check_memory+0xd/0x10 iowrite8_rep+0x86/0x380 vmci_send_datagram+0x150/0x280 vmci_dbell_register_notification_bitmap+0x133/0x1e0 vmci_guest_probe_device+0xcab/0x1e70 pci_device_probe+0xab3/0xe70 really_probe+0xd16/0x24d0 driver_probe_device+0x29d/0x3a0 device_driver_attach+0x25a/0x490 __driver_attach+0x78c/0x840 bus_for_each_dev+0x210/0x340 driver_attach+0x89/0xb0 bus_add_driver+0x677/0xc40 driver_register+0x485/0x8e0 __pci_register_driver+0x1ff/0x350 vmci_guest_init+0x3e/0x41 vmci_drv_init+0x1d6/0x43f do_one_initcall+0x39c/0x9a0 do_initcall_level+0x1d7/0x259 do_initcalls+0x127/0x1cb do_basic_setup+0x33/0x36 kernel_init_freeable+0x29a/0x3ed kernel_init+0x1f/0x840 ret_from_fork+0x1f/0x30 Local variable ----bitmap_set_msg@vmci_dbell_register_notification_bitmap created at: vmci_dbell_register_notification_bitmap+0x50/0x1e0 vmci_dbell_register_notification_bitmap+0x50/0x1e0 Bytes 28-31 of 32 are uninitialized Memory access of size 32 starts at ffff88810098f570 ===================================================== Fixes: 83e2ec7 ("VMCI: doorbell implementation.") Cc: <stable@vger.kernel.org> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/20210402121742.3917-1-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b2192cf upstream. KMSAN complains that vmci_check_host_caps() left the payload part of check_msg uninitialized. ===================================================== BUG: KMSAN: uninit-value in kmsan_check_memory+0xd/0x10 CPU: 1 PID: 1 Comm: swapper/0 Tainted: G B 5.11.0-rc7+ gregkh#4 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 02/27/2020 Call Trace: dump_stack+0x21c/0x280 kmsan_report+0xfb/0x1e0 kmsan_internal_check_memory+0x202/0x520 kmsan_check_memory+0xd/0x10 iowrite8_rep+0x86/0x380 vmci_guest_probe_device+0xf0b/0x1e70 pci_device_probe+0xab3/0xe70 really_probe+0xd16/0x24d0 driver_probe_device+0x29d/0x3a0 device_driver_attach+0x25a/0x490 __driver_attach+0x78c/0x840 bus_for_each_dev+0x210/0x340 driver_attach+0x89/0xb0 bus_add_driver+0x677/0xc40 driver_register+0x485/0x8e0 __pci_register_driver+0x1ff/0x350 vmci_guest_init+0x3e/0x41 vmci_drv_init+0x1d6/0x43f do_one_initcall+0x39c/0x9a0 do_initcall_level+0x1d7/0x259 do_initcalls+0x127/0x1cb do_basic_setup+0x33/0x36 kernel_init_freeable+0x29a/0x3ed kernel_init+0x1f/0x840 ret_from_fork+0x1f/0x30 Uninit was created at: kmsan_internal_poison_shadow+0x5c/0xf0 kmsan_slab_alloc+0x8d/0xe0 kmem_cache_alloc+0x84f/0xe30 vmci_guest_probe_device+0xd11/0x1e70 pci_device_probe+0xab3/0xe70 really_probe+0xd16/0x24d0 driver_probe_device+0x29d/0x3a0 device_driver_attach+0x25a/0x490 __driver_attach+0x78c/0x840 bus_for_each_dev+0x210/0x340 driver_attach+0x89/0xb0 bus_add_driver+0x677/0xc40 driver_register+0x485/0x8e0 __pci_register_driver+0x1ff/0x350 vmci_guest_init+0x3e/0x41 vmci_drv_init+0x1d6/0x43f do_one_initcall+0x39c/0x9a0 do_initcall_level+0x1d7/0x259 do_initcalls+0x127/0x1cb do_basic_setup+0x33/0x36 kernel_init_freeable+0x29a/0x3ed kernel_init+0x1f/0x840 ret_from_fork+0x1f/0x30 Bytes 28-31 of 36 are uninitialized Memory access of size 36 starts at ffff8881675e5f00 ===================================================== Fixes: 1f16643 ("VMCI: guest side driver implementation.") Cc: <stable@vger.kernel.org> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/20210402121742.3917-2-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2c48441 ] lz4 compatible decompressor is simple. The format is underspecified and relies on EOF notification to determine when to stop. Initramfs buffer format[1] explicitly states that it can have arbitrary number of zero padding. Thus when operating without a fill function, be extra careful to ensure that sizes less than 4, or apperantly empty chunksizes are treated as EOF. To test this I have created two cpio initrds, first a normal one, main.cpio. And second one with just a single /test-file with content "second" second.cpio. Then i compressed both of them with gzip, and with lz4 -l. Then I created a padding of 4 bytes (dd if=/dev/zero of=pad4 bs=1 count=4). To create four testcase initrds: 1) main.cpio.gzip + extra.cpio.gzip = pad0.gzip 2) main.cpio.lz4 + extra.cpio.lz4 = pad0.lz4 3) main.cpio.gzip + pad4 + extra.cpio.gzip = pad4.gzip 4) main.cpio.lz4 + pad4 + extra.cpio.lz4 = pad4.lz4 The pad4 test-cases replicate the initrd load by grub, as it pads and aligns every initrd it loads. All of the above boot, however /test-file was not accessible in the initrd for the testcase gregkh#4, as decoding in lz4 decompressor failed. Also an error message printed which usually is harmless. Whith a patched kernel, all of the above testcases now pass, and /test-file is accessible. This fixes lz4 initrd decompress warning on every boot with grub. And more importantly this fixes inability to load multiple lz4 compressed initrds with grub. This patch has been shipping in Ubuntu kernels since January 2021. [1] ./Documentation/driver-api/early-userspace/buffer-format.rst BugLink: https://bugs.launchpad.net/bugs/1835660 Link: https://lore.kernel.org/lkml/20210114200256.196589-1-xnox@ubuntu.com/ # v0 Link: https://lkml.kernel.org/r/20210513104831.432975-1-dimitri.ledkov@canonical.com Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com> Cc: Kyungsik Lee <kyungsik.lee@lge.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Bongkyu Kim <bongkyu.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Sven Schmidt <4sschmid@informatik.uni-hamburg.de> Cc: Rajat Asthana <thisisrast7@gmail.com> Cc: Nick Terrell <terrelln@fb.com> Cc: Gao Xiang <hsiangkao@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 4385539 upstream. The ordering of MSI-X enable in hardware is dysfunctional: 1) MSI-X is disabled in the control register 2) Various setup functions 3) pci_msi_setup_msi_irqs() is invoked which ends up accessing the MSI-X table entries 4) MSI-X is enabled and masked in the control register with the comment that enabling is required for some hardware to access the MSI-X table Step gregkh#4 obviously contradicts gregkh#3. The history of this is an issue with the NIU hardware. When gregkh#4 was introduced the table access actually happened in msix_program_entries() which was invoked after enabling and masking MSI-X. This was changed in commit d71d643 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") which removed the table write from msix_program_entries(). Interestingly enough nobody noticed and either NIU still works or it did not get any testing with a kernel 3.19 or later. Nevertheless this is inconsistent and there is no reason why MSI-X can't be enabled and masked in the control register early on, i.e. move step gregkh#4 above to step gregkh#1. This preserves the NIU workaround and has no side effects on other hardware. Fixes: d71d643 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2c48441 ] lz4 compatible decompressor is simple. The format is underspecified and relies on EOF notification to determine when to stop. Initramfs buffer format[1] explicitly states that it can have arbitrary number of zero padding. Thus when operating without a fill function, be extra careful to ensure that sizes less than 4, or apperantly empty chunksizes are treated as EOF. To test this I have created two cpio initrds, first a normal one, main.cpio. And second one with just a single /test-file with content "second" second.cpio. Then i compressed both of them with gzip, and with lz4 -l. Then I created a padding of 4 bytes (dd if=/dev/zero of=pad4 bs=1 count=4). To create four testcase initrds: 1) main.cpio.gzip + extra.cpio.gzip = pad0.gzip 2) main.cpio.lz4 + extra.cpio.lz4 = pad0.lz4 3) main.cpio.gzip + pad4 + extra.cpio.gzip = pad4.gzip 4) main.cpio.lz4 + pad4 + extra.cpio.lz4 = pad4.lz4 The pad4 test-cases replicate the initrd load by grub, as it pads and aligns every initrd it loads. All of the above boot, however /test-file was not accessible in the initrd for the testcase gregkh#4, as decoding in lz4 decompressor failed. Also an error message printed which usually is harmless. Whith a patched kernel, all of the above testcases now pass, and /test-file is accessible. This fixes lz4 initrd decompress warning on every boot with grub. And more importantly this fixes inability to load multiple lz4 compressed initrds with grub. This patch has been shipping in Ubuntu kernels since January 2021. [1] ./Documentation/driver-api/early-userspace/buffer-format.rst BugLink: https://bugs.launchpad.net/bugs/1835660 Link: https://lore.kernel.org/lkml/20210114200256.196589-1-xnox@ubuntu.com/ # v0 Link: https://lkml.kernel.org/r/20210513104831.432975-1-dimitri.ledkov@canonical.com Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com> Cc: Kyungsik Lee <kyungsik.lee@lge.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Bongkyu Kim <bongkyu.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Sven Schmidt <4sschmid@informatik.uni-hamburg.de> Cc: Rajat Asthana <thisisrast7@gmail.com> Cc: Nick Terrell <terrelln@fb.com> Cc: Gao Xiang <hsiangkao@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 4385539 upstream. The ordering of MSI-X enable in hardware is dysfunctional: 1) MSI-X is disabled in the control register 2) Various setup functions 3) pci_msi_setup_msi_irqs() is invoked which ends up accessing the MSI-X table entries 4) MSI-X is enabled and masked in the control register with the comment that enabling is required for some hardware to access the MSI-X table Step gregkh#4 obviously contradicts gregkh#3. The history of this is an issue with the NIU hardware. When gregkh#4 was introduced the table access actually happened in msix_program_entries() which was invoked after enabling and masking MSI-X. This was changed in commit d71d643 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") which removed the table write from msix_program_entries(). Interestingly enough nobody noticed and either NIU still works or it did not get any testing with a kernel 3.19 or later. Nevertheless this is inconsistent and there is no reason why MSI-X can't be enabled and masked in the control register early on, i.e. move step gregkh#4 above to step gregkh#1. This preserves the NIU workaround and has no side effects on other hardware. Fixes: d71d643 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 376565b upstream. KMSAN complains that the vmci_use_ppn64() == false path in vmci_dbell_register_notification_bitmap() left upper 32bits of bitmap_set_msg.bitmap_ppn64 member uninitialized. ===================================================== BUG: KMSAN: uninit-value in kmsan_check_memory+0xd/0x10 CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.11.0-rc7+ gregkh#4 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 02/27/2020 Call Trace: dump_stack+0x21c/0x280 kmsan_report+0xfb/0x1e0 kmsan_internal_check_memory+0x484/0x520 kmsan_check_memory+0xd/0x10 iowrite8_rep+0x86/0x380 vmci_send_datagram+0x150/0x280 vmci_dbell_register_notification_bitmap+0x133/0x1e0 vmci_guest_probe_device+0xcab/0x1e70 pci_device_probe+0xab3/0xe70 really_probe+0xd16/0x24d0 driver_probe_device+0x29d/0x3a0 device_driver_attach+0x25a/0x490 __driver_attach+0x78c/0x840 bus_for_each_dev+0x210/0x340 driver_attach+0x89/0xb0 bus_add_driver+0x677/0xc40 driver_register+0x485/0x8e0 __pci_register_driver+0x1ff/0x350 vmci_guest_init+0x3e/0x41 vmci_drv_init+0x1d6/0x43f do_one_initcall+0x39c/0x9a0 do_initcall_level+0x1d7/0x259 do_initcalls+0x127/0x1cb do_basic_setup+0x33/0x36 kernel_init_freeable+0x29a/0x3ed kernel_init+0x1f/0x840 ret_from_fork+0x1f/0x30 Local variable ----bitmap_set_msg@vmci_dbell_register_notification_bitmap created at: vmci_dbell_register_notification_bitmap+0x50/0x1e0 vmci_dbell_register_notification_bitmap+0x50/0x1e0 Bytes 28-31 of 32 are uninitialized Memory access of size 32 starts at ffff88810098f570 ===================================================== Fixes: 83e2ec7 ("VMCI: doorbell implementation.") Cc: <stable@vger.kernel.org> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/20210402121742.3917-1-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b2192cf upstream. KMSAN complains that vmci_check_host_caps() left the payload part of check_msg uninitialized. ===================================================== BUG: KMSAN: uninit-value in kmsan_check_memory+0xd/0x10 CPU: 1 PID: 1 Comm: swapper/0 Tainted: G B 5.11.0-rc7+ gregkh#4 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 02/27/2020 Call Trace: dump_stack+0x21c/0x280 kmsan_report+0xfb/0x1e0 kmsan_internal_check_memory+0x202/0x520 kmsan_check_memory+0xd/0x10 iowrite8_rep+0x86/0x380 vmci_guest_probe_device+0xf0b/0x1e70 pci_device_probe+0xab3/0xe70 really_probe+0xd16/0x24d0 driver_probe_device+0x29d/0x3a0 device_driver_attach+0x25a/0x490 __driver_attach+0x78c/0x840 bus_for_each_dev+0x210/0x340 driver_attach+0x89/0xb0 bus_add_driver+0x677/0xc40 driver_register+0x485/0x8e0 __pci_register_driver+0x1ff/0x350 vmci_guest_init+0x3e/0x41 vmci_drv_init+0x1d6/0x43f do_one_initcall+0x39c/0x9a0 do_initcall_level+0x1d7/0x259 do_initcalls+0x127/0x1cb do_basic_setup+0x33/0x36 kernel_init_freeable+0x29a/0x3ed kernel_init+0x1f/0x840 ret_from_fork+0x1f/0x30 Uninit was created at: kmsan_internal_poison_shadow+0x5c/0xf0 kmsan_slab_alloc+0x8d/0xe0 kmem_cache_alloc+0x84f/0xe30 vmci_guest_probe_device+0xd11/0x1e70 pci_device_probe+0xab3/0xe70 really_probe+0xd16/0x24d0 driver_probe_device+0x29d/0x3a0 device_driver_attach+0x25a/0x490 __driver_attach+0x78c/0x840 bus_for_each_dev+0x210/0x340 driver_attach+0x89/0xb0 bus_add_driver+0x677/0xc40 driver_register+0x485/0x8e0 __pci_register_driver+0x1ff/0x350 vmci_guest_init+0x3e/0x41 vmci_drv_init+0x1d6/0x43f do_one_initcall+0x39c/0x9a0 do_initcall_level+0x1d7/0x259 do_initcalls+0x127/0x1cb do_basic_setup+0x33/0x36 kernel_init_freeable+0x29a/0x3ed kernel_init+0x1f/0x840 ret_from_fork+0x1f/0x30 Bytes 28-31 of 36 are uninitialized Memory access of size 36 starts at ffff8881675e5f00 ===================================================== Fixes: 1f16643 ("VMCI: guest side driver implementation.") Cc: <stable@vger.kernel.org> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/20210402121742.3917-2-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit eedf3e3 ] ACPICA commit 1c28da2242783579d59767617121035dafba18c3 This was originally done in NetBSD: NetBSD/src@b69d1ac and is the correct alternative to the smattering of `memcpy`s I previously contributed to this repository. This also sidesteps the newly strict checks added in UBSAN: llvm/llvm-project@7926744 Before this change we see the following UBSAN stack trace in Fuchsia: #0 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e #1.2 0x000021982bc4af3c in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x41f3c #1.1 0x000021982bc4af3c in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x41f3c #1 0x000021982bc4af3c in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:395 <libclang_rt.asan.so>+0x41f3c #2 0x000021982bc4bb6f in handletype_mismatch_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:137 <libclang_rt.asan.so>+0x42b6f #3 0x000021982bc4b723 in __ubsan_handle_type_mismatch_v1 compiler-rt/lib/ubsan/ubsan_handlers.cpp:142 <libclang_rt.asan.so>+0x42723 #4 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e #5 0x000021afcfdf2089 in acpi_rs_convert_aml_to_resource(struct acpi_resource*, union aml_resource*, struct acpi_rsconvert_info*) ../../third_party/acpica/source/components/resources/rsmisc.c:355 <platform-bus-x86.so>+0x6b2089 #6 0x000021afcfded169 in acpi_rs_convert_aml_to_resources(u8*, u32, u32, u8, void**) ../../third_party/acpica/source/components/resources/rslist.c:137 <platform-bus-x86.so>+0x6ad169 #7 0x000021afcfe2d24a in acpi_ut_walk_aml_resources(struct acpi_walk_state*, u8*, acpi_size, acpi_walk_aml_callback, void**) ../../third_party/acpica/source/components/utilities/utresrc.c:237 <platform-bus-x86.so>+0x6ed24a #8 0x000021afcfde66b7 in acpi_rs_create_resource_list(union acpi_operand_object*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rscreate.c:199 <platform-bus-x86.so>+0x6a66b7 #9 0x000021afcfdf6979 in acpi_rs_get_method_data(acpi_handle, const char*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rsutils.c:770 <platform-bus-x86.so>+0x6b6979 #10 0x000021afcfdf708f in acpi_walk_resources(acpi_handle, char*, acpi_walk_resource_callback, void*) ../../third_party/acpica/source/components/resources/rsxface.c:731 <platform-bus-x86.so>+0x6b708f #11 0x000021afcfa95dcf in acpi::acpi_impl::walk_resources(acpi::acpi_impl*, acpi_handle, const char*, acpi::Acpi::resources_callable) ../../src/devices/board/lib/acpi/acpi-impl.cc:41 <platform-bus-x86.so>+0x355dcf #12 0x000021afcfaa8278 in acpi::device_builder::gather_resources(acpi::device_builder*, acpi::Acpi*, fidl::any_arena&, acpi::Manager*, acpi::device_builder::gather_resources_callback) ../../src/devices/board/lib/acpi/device-builder.cc:84 <platform-bus-x86.so>+0x368278 #13 0x000021afcfbddb87 in acpi::Manager::configure_discovered_devices(acpi::Manager*) ../../src/devices/board/lib/acpi/manager.cc:75 <platform-bus-x86.so>+0x49db87 #14 0x000021afcf99091d in publish_acpi_devices(acpi::Manager*, zx_device_t*, zx_device_t*) ../../src/devices/board/drivers/x86/acpi-nswalk.cc:95 <platform-bus-x86.so>+0x25091d #15 0x000021afcf9c1d4e in x86::X86::do_init(x86::X86*) ../../src/devices/board/drivers/x86/x86.cc:60 <platform-bus-x86.so>+0x281d4e #16 0x000021afcf9e33ad in λ(x86::X86::ddk_init::(anon class)*) ../../src/devices/board/drivers/x86/x86.cc:77 <platform-bus-x86.so>+0x2a33ad #17 0x000021afcf9e313e in fit::internal::target<(lambda at../../src/devices/board/drivers/x86/x86.cc:76:19), false, false, std::__2::allocator<std::byte>, void>::invoke(void*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:183 <platform-bus-x86.so>+0x2a313e #18 0x000021afcfbab4c7 in fit::internal::function_base<16UL, false, void(), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <platform-bus-x86.so>+0x46b4c7 #19 0x000021afcfbab342 in fit::function_impl<16UL, false, void(), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/function.h:315 <platform-bus-x86.so>+0x46b342 #20 0x000021afcfcd98c3 in async::internal::retained_task::Handler(async_dispatcher_t*, async_task_t*, zx_status_t) ../../sdk/lib/async/task.cc:24 <platform-bus-x86.so>+0x5998c3 #21 0x00002290f9924616 in λ(const driver_runtime::Dispatcher::post_task::(anon class)*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/dispatcher.cc:789 <libdriver_runtime.so>+0x10a616 #22 0x00002290f9924323 in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:788:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int>::invoke(void*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0x10a323 #23 0x00002290f9904b76 in fit::internal::function_base<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xeab76 #24 0x00002290f9904831 in fit::callback_impl<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::operator()(fit::callback_impl<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/function.h:471 <libdriver_runtime.so>+0xea831 #25 0x00002290f98d5adc in driver_runtime::callback_request::Call(driver_runtime::callback_request*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/callback_request.h:74 <libdriver_runtime.so>+0xbbadc #26 0x00002290f98e1e58 in driver_runtime::Dispatcher::dispatch_callback(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >) ../../src/devices/bin/driver_runtime/dispatcher.cc:1248 <libdriver_runtime.so>+0xc7e58 #27 0x00002290f98e4159 in driver_runtime::Dispatcher::dispatch_callbacks(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:1308 <libdriver_runtime.so>+0xca159 #28 0x00002290f9918414 in λ(const driver_runtime::Dispatcher::create_with_adder::(anon class)*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:353 <libdriver_runtime.so>+0xfe414 #29 0x00002290f991812d in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:351:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>>::invoke(void*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0xfe12d #30 0x00002290f9906fc7 in fit::internal::function_base<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xecfc7 #31 0x00002290f9906c66 in fit::function_impl<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/function.h:315 <libdriver_runtime.so>+0xecc66 #32 0x00002290f98e73d9 in driver_runtime::Dispatcher::event_waiter::invoke_callback(driver_runtime::Dispatcher::event_waiter*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.h:543 <libdriver_runtime.so>+0xcd3d9 #33 0x00002290f98e700d in driver_runtime::Dispatcher::event_waiter::handle_event(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/dispatcher.cc:1442 <libdriver_runtime.so>+0xcd00d #34 0x00002290f9918983 in async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event(async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>*, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/async_loop_owned_event_handler.h:59 <libdriver_runtime.so>+0xfe983 #35 0x00002290f9918b9e in async::wait_method<async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>, &async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event>::call_handler(async_dispatcher_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async/include/lib/async/cpp/wait.h:201 <libdriver_runtime.so>+0xfeb9e #36 0x00002290f99bf509 in async_loop_dispatch_wait(async_loop_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async-loop/loop.c:394 <libdriver_runtime.so>+0x1a5509 #37 0x00002290f99b9958 in async_loop_run_once(async_loop_t*, zx_time_t) ../../sdk/lib/async-loop/loop.c:343 <libdriver_runtime.so>+0x19f958 #38 0x00002290f99b9247 in async_loop_run(async_loop_t*, zx_time_t, _Bool) ../../sdk/lib/async-loop/loop.c:301 <libdriver_runtime.so>+0x19f247 #39 0x00002290f99ba962 in async_loop_run_thread(void*) ../../sdk/lib/async-loop/loop.c:860 <libdriver_runtime.so>+0x1a0962 #40 0x000041afd176ef30 in start_c11(void*) ../../zircon/third_party/ulib/musl/pthread/pthread_create.c:63 <libc.so>+0x84f30 #41 0x000041afd18a448d in thread_trampoline(uintptr_t, uintptr_t) ../../zircon/system/ulib/runtime/thread.cc:100 <libc.so>+0x1ba48d Link: acpica/acpica@1c28da22 Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/4664267.LvFx2qVVIh@rjwysocki.net Signed-off-by: Tamir Duberstein <tamird@gmail.com> [ rjw: Pick up the tag from Tamir ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1e9ac33 ] Before the commit under the Fixes tag below, bnxt_ulp_stop() and bnxt_ulp_start() were always invoked in pairs. After that commit, the new bnxt_ulp_restart() can be invoked after bnxt_ulp_stop() has been called. This may result in the RoCE driver's aux driver .suspend() method being invoked twice. The 2nd bnxt_re_suspend() call will crash when it dereferences a NULL pointer: (NULL ib_device): Handle device suspend call BUG: kernel NULL pointer dereference, address: 0000000000000b78 PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI CPU: 20 UID: 0 PID: 181 Comm: kworker/u96:5 Tainted: G S 6.15.0-rc1 #4 PREEMPT(voluntary) Tainted: [S]=CPU_OUT_OF_SPEC Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.4.3 01/17/2017 Workqueue: bnxt_pf_wq bnxt_sp_task [bnxt_en] RIP: 0010:bnxt_re_suspend+0x45/0x1f0 [bnxt_re] Code: 8b 05 a7 3c 5b f5 48 89 44 24 18 31 c0 49 8b 5c 24 08 4d 8b 2c 24 e8 ea 06 0a f4 48 c7 c6 04 60 52 c0 48 89 df e8 1b ce f9 ff <48> 8b 83 78 0b 00 00 48 8b 80 38 03 00 00 a8 40 0f 85 b5 00 00 00 RSP: 0018:ffffa2e84084fd88 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000001 RDX: 0000000000000000 RSI: ffffffffb4b6b934 RDI: 00000000ffffffff RBP: ffffa1760954c9c0 R08: 0000000000000000 R09: c0000000ffffdfff R10: 0000000000000001 R11: ffffa2e84084fb50 R12: ffffa176031ef070 R13: ffffa17609775000 R14: ffffa17603adc180 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffffa17daa397000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000b78 CR3: 00000004aaa30003 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> bnxt_ulp_stop+0x69/0x90 [bnxt_en] bnxt_sp_task+0x678/0x920 [bnxt_en] ? __schedule+0x514/0xf50 process_scheduled_works+0x9d/0x400 worker_thread+0x11c/0x260 ? __pfx_worker_thread+0x10/0x10 kthread+0xfe/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2b/0x40 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 Check the BNXT_EN_FLAG_ULP_STOPPED flag and do not proceed if the flag is already set. This will preserve the original symmetrical bnxt_ulp_stop() and bnxt_ulp_start(). Also, inside bnxt_ulp_start(), clear the BNXT_EN_FLAG_ULP_STOPPED flag after taking the mutex to avoid any race condition. And for symmetry, only proceed in bnxt_ulp_start() if the BNXT_EN_FLAG_ULP_STOPPED is set. Fixes: 3c163f3 ("bnxt_en: Optimize recovery path ULP locking in the driver") Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Co-developed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250613231841.377988-2-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit be6e843 upstream. When migrating a THP, concurrent access to the PMD migration entry during a deferred split scan can lead to an invalid address access, as illustrated below. To prevent this invalid access, it is necessary to check the PMD migration entry and return early. In this context, there is no need to use pmd_to_swp_entry and pfn_swap_entry_to_page to verify the equality of the target folio. Since the PMD migration entry is locked, it cannot be served as the target. Mailing list discussion and explanation from Hugh Dickins: "An anon_vma lookup points to a location which may contain the folio of interest, but might instead contain another folio: and weeding out those other folios is precisely what the "folio != pmd_folio((*pmd)" check (and the "risk of replacing the wrong folio" comment a few lines above it) is for." BUG: unable to handle page fault for address: ffffea60001db008 CPU: 0 UID: 0 PID: 2199114 Comm: tee Not tainted 6.14.0+ #4 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:split_huge_pmd_locked+0x3b5/0x2b60 Call Trace: <TASK> try_to_migrate_one+0x28c/0x3730 rmap_walk_anon+0x4f6/0x770 unmap_folio+0x196/0x1f0 split_huge_page_to_list_to_order+0x9f6/0x1560 deferred_split_scan+0xac5/0x12a0 shrinker_debugfs_scan_write+0x376/0x470 full_proxy_write+0x15c/0x220 vfs_write+0x2fc/0xcb0 ksys_write+0x146/0x250 do_syscall_64+0x6a/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e The bug is found by syzkaller on an internal kernel, then confirmed on upstream. Link: https://lkml.kernel.org/r/20250421113536.3682201-1-gavinguo@igalia.com Link: https://lore.kernel.org/all/20250414072737.1698513-1-gavinguo@igalia.com/ Link: https://lore.kernel.org/all/20250418085802.2973519-1-gavinguo@igalia.com/ Fixes: 84c3fc4 ("mm: thp: check pmd migration entry in common path") Signed-off-by: Gavin Guo <gavinguo@igalia.com> Acked-by: David Hildenbrand <david@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Zi Yan <ziy@nvidia.com> Reviewed-by: Gavin Shan <gshan@redhat.com> Cc: Florent Revest <revest@google.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> [gavin: backport the migration checking logic to __split_huge_pmd] Signed-off-by: Gavin Guo <gavinguo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ee684de ] As shown in [1], it is possible to corrupt a BPF ELF file such that arbitrary BPF instructions are loaded by libbpf. This can be done by setting a symbol (BPF program) section offset to a large (unsigned) number such that <section start + symbol offset> overflows and points before the section data in the memory. Consider the situation below where: - prog_start = sec_start + symbol_offset <-- size_t overflow here - prog_end = prog_start + prog_size prog_start sec_start prog_end sec_end | | | | v v v v .....................|################################|............ The report in [1] also provides a corrupted BPF ELF which can be used as a reproducer: $ readelf -S crash Section Headers: [Nr] Name Type Address Offset Size EntSize Flags Link Info Align ... [ 2] uretprobe.mu[...] PROGBITS 0000000000000000 00000040 0000000000000068 0000000000000000 AX 0 0 8 $ readelf -s crash Symbol table '.symtab' contains 8 entries: Num: Value Size Type Bind Vis Ndx Name ... 6: ffffffffffffffb8 104 FUNC GLOBAL DEFAULT 2 handle_tp Here, the handle_tp prog has section offset ffffffffffffffb8, i.e. will point before the actual memory where section 2 is allocated. This is also reported by AddressSanitizer: ================================================================= ==1232==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x7c7302fe0000 at pc 0x7fc3046e4b77 bp 0x7ffe64677cd0 sp 0x7ffe64677490 READ of size 104 at 0x7c7302fe0000 thread T0 #0 0x7fc3046e4b76 in memcpy (/lib64/libasan.so.8+0xe4b76) #1 0x00000040df3e in bpf_object__init_prog /src/libbpf/src/libbpf.c:856 #2 0x00000040df3e in bpf_object__add_programs /src/libbpf/src/libbpf.c:928 #3 0x00000040df3e in bpf_object__elf_collect /src/libbpf/src/libbpf.c:3930 #4 0x00000040df3e in bpf_object_open /src/libbpf/src/libbpf.c:8067 #5 0x00000040f176 in bpf_object__open_file /src/libbpf/src/libbpf.c:8090 #6 0x000000400c16 in main /poc/poc.c:8 #7 0x7fc3043d25b4 in __libc_start_call_main (/lib64/libc.so.6+0x35b4) #8 0x7fc3043d2667 in __libc_start_main@@GLIBC_2.34 (/lib64/libc.so.6+0x3667) #9 0x000000400b34 in _start (/poc/poc+0x400b34) 0x7c7302fe0000 is located 64 bytes before 104-byte region [0x7c7302fe0040,0x7c7302fe00a8) allocated by thread T0 here: #0 0x7fc3046e716b in malloc (/lib64/libasan.so.8+0xe716b) #1 0x7fc3045ee600 in __libelf_set_rawdata_wrlock (/lib64/libelf.so.1+0xb600) #2 0x7fc3045ef018 in __elf_getdata_rdlock (/lib64/libelf.so.1+0xc018) #3 0x00000040642f in elf_sec_data /src/libbpf/src/libbpf.c:3740 The problem here is that currently, libbpf only checks that the program end is within the section bounds. There used to be a check `while (sec_off < sec_sz)` in bpf_object__add_programs, however, it was removed by commit 6245947 ("libbpf: Allow gaps in BPF program sections to support overriden weak functions"). Add a check for detecting the overflow of `sec_off + prog_sz` to bpf_object__init_prog to fix this issue. [1] https://github.com/lmarch2/poc/blob/main/libbpf/libbpf.md Fixes: 6245947 ("libbpf: Allow gaps in BPF program sections to support overriden weak functions") Reported-by: lmarch2 <2524158037@qq.com> Signed-off-by: Viktor Malik <vmalik@redhat.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reviewed-by: Shung-Hsi Yu <shung-hsi.yu@suse.com> Link: https://github.com/lmarch2/poc/blob/main/libbpf/libbpf.md Link: https://lore.kernel.org/bpf/20250415155014.397603-1-vmalik@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>

commit be6e843 upstream. When migrating a THP, concurrent access to the PMD migration entry during a deferred split scan can lead to an invalid address access, as illustrated below. To prevent this invalid access, it is necessary to check the PMD migration entry and return early. In this context, there is no need to use pmd_to_swp_entry and pfn_swap_entry_to_page to verify the equality of the target folio. Since the PMD migration entry is locked, it cannot be served as the target. Mailing list discussion and explanation from Hugh Dickins: "An anon_vma lookup points to a location which may contain the folio of interest, but might instead contain another folio: and weeding out those other folios is precisely what the "folio != pmd_folio((*pmd)" check (and the "risk of replacing the wrong folio" comment a few lines above it) is for." BUG: unable to handle page fault for address: ffffea60001db008 CPU: 0 UID: 0 PID: 2199114 Comm: tee Not tainted 6.14.0+ #4 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:split_huge_pmd_locked+0x3b5/0x2b60 Call Trace: <TASK> try_to_migrate_one+0x28c/0x3730 rmap_walk_anon+0x4f6/0x770 unmap_folio+0x196/0x1f0 split_huge_page_to_list_to_order+0x9f6/0x1560 deferred_split_scan+0xac5/0x12a0 shrinker_debugfs_scan_write+0x376/0x470 full_proxy_write+0x15c/0x220 vfs_write+0x2fc/0xcb0 ksys_write+0x146/0x250 do_syscall_64+0x6a/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e The bug is found by syzkaller on an internal kernel, then confirmed on upstream. Link: https://lkml.kernel.org/r/20250421113536.3682201-1-gavinguo@igalia.com Link: https://lore.kernel.org/all/20250414072737.1698513-1-gavinguo@igalia.com/ Link: https://lore.kernel.org/all/20250418085802.2973519-1-gavinguo@igalia.com/ Fixes: 84c3fc4 ("mm: thp: check pmd migration entry in common path") Signed-off-by: Gavin Guo <gavinguo@igalia.com> Acked-by: David Hildenbrand <david@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Zi Yan <ziy@nvidia.com> Reviewed-by: Gavin Shan <gshan@redhat.com> Cc: Florent Revest <revest@google.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> [gavin: backport the migration checking logic to __split_huge_pmd] Signed-off-by: Gavin Guo <gavinguo@igalia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

… context The current use of a mutex to protect the notifier hashtable accesses can lead to issues in the atomic context. It results in the below kernel warnings: | BUG: sleeping function called from invalid context at kernel/locking/mutex.c:258 | in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 9, name: kworker/0:0 | preempt_count: 1, expected: 0 | RCU nest depth: 0, expected: 0 | CPU: 0 UID: 0 PID: 9 Comm: kworker/0:0 Not tainted 6.14.0 gregkh#4 | Workqueue: ffa_pcpu_irq_notification notif_pcpu_irq_work_fn | Call trace: | show_stack+0x18/0x24 (C) | dump_stack_lvl+0x78/0x90 | dump_stack+0x18/0x24 | __might_resched+0x114/0x170 | __might_sleep+0x48/0x98 | mutex_lock+0x24/0x80 | handle_notif_callbacks+0x54/0xe0 | notif_get_and_handle+0x40/0x88 | generic_exec_single+0x80/0xc0 | smp_call_function_single+0xfc/0x1a0 | notif_pcpu_irq_work_fn+0x2c/0x38 | process_one_work+0x14c/0x2b4 | worker_thread+0x2e4/0x3e0 | kthread+0x13c/0x210 | ret_from_fork+0x10/0x20 To address this, replace the mutex with an rwlock to protect the notifier hashtable accesses. This ensures that read-side locking does not sleep and multiple readers can acquire the lock concurrently, avoiding unnecessary contention and potential deadlocks. Writer access remains exclusive, preserving correctness. This change resolves warnings from lockdep about potential sleep in atomic context. Cc: Jens Wiklander <jens.wiklander@linaro.org> Reported-by: Jérôme Forissier <jerome.forissier@linaro.org> Closes: OP-TEE/optee_os#7394 Fixes: e057344 ("firmware: arm_ffa: Add interfaces to request notification callbacks") Message-Id: <20250528-ffa_notif_fix-v1-3-5ed7bc7f8437@arm.com> Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org> Tested-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

… context commit 9ca7a42 upstream. The current use of a mutex to protect the notifier hashtable accesses can lead to issues in the atomic context. It results in the below kernel warnings: | BUG: sleeping function called from invalid context at kernel/locking/mutex.c:258 | in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 9, name: kworker/0:0 | preempt_count: 1, expected: 0 | RCU nest depth: 0, expected: 0 | CPU: 0 UID: 0 PID: 9 Comm: kworker/0:0 Not tainted 6.14.0 gregkh#4 | Workqueue: ffa_pcpu_irq_notification notif_pcpu_irq_work_fn | Call trace: | show_stack+0x18/0x24 (C) | dump_stack_lvl+0x78/0x90 | dump_stack+0x18/0x24 | __might_resched+0x114/0x170 | __might_sleep+0x48/0x98 | mutex_lock+0x24/0x80 | handle_notif_callbacks+0x54/0xe0 | notif_get_and_handle+0x40/0x88 | generic_exec_single+0x80/0xc0 | smp_call_function_single+0xfc/0x1a0 | notif_pcpu_irq_work_fn+0x2c/0x38 | process_one_work+0x14c/0x2b4 | worker_thread+0x2e4/0x3e0 | kthread+0x13c/0x210 | ret_from_fork+0x10/0x20 To address this, replace the mutex with an rwlock to protect the notifier hashtable accesses. This ensures that read-side locking does not sleep and multiple readers can acquire the lock concurrently, avoiding unnecessary contention and potential deadlocks. Writer access remains exclusive, preserving correctness. This change resolves warnings from lockdep about potential sleep in atomic context. Cc: Jens Wiklander <jens.wiklander@linaro.org> Reported-by: Jérôme Forissier <jerome.forissier@linaro.org> Closes: OP-TEE/optee_os#7394 Fixes: e057344 ("firmware: arm_ffa: Add interfaces to request notification callbacks") Message-Id: <20250528-ffa_notif_fix-v1-3-5ed7bc7f8437@arm.com> Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org> Tested-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

… context [ Upstream commit 9ca7a42 ] The current use of a mutex to protect the notifier hashtable accesses can lead to issues in the atomic context. It results in the below kernel warnings: | BUG: sleeping function called from invalid context at kernel/locking/mutex.c:258 | in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 9, name: kworker/0:0 | preempt_count: 1, expected: 0 | RCU nest depth: 0, expected: 0 | CPU: 0 UID: 0 PID: 9 Comm: kworker/0:0 Not tainted 6.14.0 gregkh#4 | Workqueue: ffa_pcpu_irq_notification notif_pcpu_irq_work_fn | Call trace: | show_stack+0x18/0x24 (C) | dump_stack_lvl+0x78/0x90 | dump_stack+0x18/0x24 | __might_resched+0x114/0x170 | __might_sleep+0x48/0x98 | mutex_lock+0x24/0x80 | handle_notif_callbacks+0x54/0xe0 | notif_get_and_handle+0x40/0x88 | generic_exec_single+0x80/0xc0 | smp_call_function_single+0xfc/0x1a0 | notif_pcpu_irq_work_fn+0x2c/0x38 | process_one_work+0x14c/0x2b4 | worker_thread+0x2e4/0x3e0 | kthread+0x13c/0x210 | ret_from_fork+0x10/0x20 To address this, replace the mutex with an rwlock to protect the notifier hashtable accesses. This ensures that read-side locking does not sleep and multiple readers can acquire the lock concurrently, avoiding unnecessary contention and potential deadlocks. Writer access remains exclusive, preserving correctness. This change resolves warnings from lockdep about potential sleep in atomic context. Cc: Jens Wiklander <jens.wiklander@linaro.org> Reported-by: Jérôme Forissier <jerome.forissier@linaro.org> Closes: OP-TEE/optee_os#7394 Fixes: e057344 ("firmware: arm_ffa: Add interfaces to request notification callbacks") Message-Id: <20250528-ffa_notif_fix-v1-3-5ed7bc7f8437@arm.com> Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org> Tested-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

…ux/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 6.16, take gregkh#4 - Gracefully fail initialising pKVM if the interrupt controller isn't GICv3 - Also gracefully fail initialising pKVM if the carveout allocation fails - Fix the computing of the minimum MMIO range required for the host on stage-2 fault - Fix the generation of the GICv3 Maintenance Interrupt in nested mode

Add the SM6115 MDSS compatible to clients compatible list, as it also needs that workaround. Without this workaround, for example, QRB4210 RB2 which is based on SM4250/SM6115 generates a lot of smmu unhandled context faults during boot: arm_smmu_context_fault: 116854 callbacks suppressed arm-smmu c600000.iommu: Unhandled context fault: fsr=0x402, iova=0x5c0ec600, fsynr=0x320021, cbfrsynra=0x420, cb=5 arm-smmu c600000.iommu: FSR = 00000402 [Format=2 TF], SID=0x420 arm-smmu c600000.iommu: FSYNR0 = 00320021 [S1CBNDX=50 PNU PLVL=1] arm-smmu c600000.iommu: Unhandled context fault: fsr=0x402, iova=0x5c0d7800, fsynr=0x320021, cbfrsynra=0x420, cb=5 arm-smmu c600000.iommu: FSR = 00000402 [Format=2 TF], SID=0x420 and also failed initialisation of lontium lt9611uxc, gpu and dpu is observed: (binding MDSS components triggered by lt9611uxc have failed) ------------[ cut here ]------------ !aspace WARNING: CPU: 6 PID: 324 at drivers/gpu/drm/msm/msm_gem_vma.c:130 msm_gem_vma_init+0x150/0x18c [msm] Modules linked in: ... (long list of modules) CPU: 6 UID: 0 PID: 324 Comm: (udev-worker) Not tainted 6.15.0-03037-gaacc73ceeb8b gregkh#4 PREEMPT Hardware name: Qualcomm Technologies, Inc. QRB4210 RB2 (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : msm_gem_vma_init+0x150/0x18c [msm] lr : msm_gem_vma_init+0x150/0x18c [msm] sp : ffff80008144b280 ... Call trace: msm_gem_vma_init+0x150/0x18c [msm] (P) get_vma_locked+0xc0/0x194 [msm] msm_gem_get_and_pin_iova_range+0x4c/0xdc [msm] msm_gem_kernel_new+0x48/0x160 [msm] msm_gpu_init+0x34c/0x53c [msm] adreno_gpu_init+0x1b0/0x2d8 [msm] a6xx_gpu_init+0x1e8/0x9e0 [msm] adreno_bind+0x2b8/0x348 [msm] component_bind_all+0x100/0x230 msm_drm_bind+0x13c/0x3d0 [msm] try_to_bring_up_aggregate_device+0x164/0x1d0 __component_add+0xa4/0x174 component_add+0x14/0x20 dsi_dev_attach+0x20/0x34 [msm] dsi_host_attach+0x58/0x98 [msm] devm_mipi_dsi_attach+0x34/0x90 lt9611uxc_attach_dsi.isra.0+0x94/0x124 [lontium_lt9611uxc] lt9611uxc_probe+0x540/0x5fc [lontium_lt9611uxc] i2c_device_probe+0x148/0x2a8 really_probe+0xbc/0x2c0 __driver_probe_device+0x78/0x120 driver_probe_device+0x3c/0x154 __driver_attach+0x90/0x1a0 bus_for_each_dev+0x68/0xb8 driver_attach+0x24/0x30 bus_add_driver+0xe4/0x208 driver_register+0x68/0x124 i2c_register_driver+0x48/0xcc lt9611uxc_driver_init+0x20/0x1000 [lontium_lt9611uxc] do_one_initcall+0x60/0x1d4 do_init_module+0x54/0x1fc load_module+0x1748/0x1c8c init_module_from_file+0x74/0xa0 __arm64_sys_finit_module+0x130/0x2f8 invoke_syscall+0x48/0x104 el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x2c/0x80 el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c ---[ end trace 0000000000000000 ]--- msm_dpu 5e01000.display-controller: [drm:msm_gpu_init [msm]] *ERROR* could not allocate memptrs: -22 msm_dpu 5e01000.display-controller: failed to load adreno gpu platform a400000.remoteproc:glink-edge:apr:service@7:dais: Adding to iommu group 19 msm_dpu 5e01000.display-controller: failed to bind 5900000.gpu (ops a3xx_ops [msm]): -22 msm_dpu 5e01000.display-controller: adev bind failed: -22 lt9611uxc 0-002b: failed to attach dsi to host lt9611uxc 0-002b: probe with driver lt9611uxc failed with error -22 Suggested-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Fixes: 3581b70 ("drm/msm/disp/dpu1: add support for display on SM6115") Cc: stable@vger.kernel.org Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> Link: https://lore.kernel.org/r/20250613173238.15061-1-alexey.klimov@linaro.org Signed-off-by: Will Deacon <will@kernel.org>

[ Upstream commit eedf3e3 ] ACPICA commit 1c28da2242783579d59767617121035dafba18c3 This was originally done in NetBSD: NetBSD/src@b69d1ac and is the correct alternative to the smattering of `memcpy`s I previously contributed to this repository. This also sidesteps the newly strict checks added in UBSAN: llvm/llvm-project@7926744 Before this change we see the following UBSAN stack trace in Fuchsia: #0 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e gregkh#1.2 0x000021982bc4af3c in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x41f3c gregkh#1.1 0x000021982bc4af3c in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x41f3c gregkh#1 0x000021982bc4af3c in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:395 <libclang_rt.asan.so>+0x41f3c gregkh#2 0x000021982bc4bb6f in handletype_mismatch_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:137 <libclang_rt.asan.so>+0x42b6f gregkh#3 0x000021982bc4b723 in __ubsan_handle_type_mismatch_v1 compiler-rt/lib/ubsan/ubsan_handlers.cpp:142 <libclang_rt.asan.so>+0x42723 gregkh#4 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e gregkh#5 0x000021afcfdf2089 in acpi_rs_convert_aml_to_resource(struct acpi_resource*, union aml_resource*, struct acpi_rsconvert_info*) ../../third_party/acpica/source/components/resources/rsmisc.c:355 <platform-bus-x86.so>+0x6b2089 gregkh#6 0x000021afcfded169 in acpi_rs_convert_aml_to_resources(u8*, u32, u32, u8, void**) ../../third_party/acpica/source/components/resources/rslist.c:137 <platform-bus-x86.so>+0x6ad169 gregkh#7 0x000021afcfe2d24a in acpi_ut_walk_aml_resources(struct acpi_walk_state*, u8*, acpi_size, acpi_walk_aml_callback, void**) ../../third_party/acpica/source/components/utilities/utresrc.c:237 <platform-bus-x86.so>+0x6ed24a gregkh#8 0x000021afcfde66b7 in acpi_rs_create_resource_list(union acpi_operand_object*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rscreate.c:199 <platform-bus-x86.so>+0x6a66b7 gregkh#9 0x000021afcfdf6979 in acpi_rs_get_method_data(acpi_handle, const char*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rsutils.c:770 <platform-bus-x86.so>+0x6b6979 gregkh#10 0x000021afcfdf708f in acpi_walk_resources(acpi_handle, char*, acpi_walk_resource_callback, void*) ../../third_party/acpica/source/components/resources/rsxface.c:731 <platform-bus-x86.so>+0x6b708f gregkh#11 0x000021afcfa95dcf in acpi::acpi_impl::walk_resources(acpi::acpi_impl*, acpi_handle, const char*, acpi::Acpi::resources_callable) ../../src/devices/board/lib/acpi/acpi-impl.cc:41 <platform-bus-x86.so>+0x355dcf gregkh#12 0x000021afcfaa8278 in acpi::device_builder::gather_resources(acpi::device_builder*, acpi::Acpi*, fidl::any_arena&, acpi::Manager*, acpi::device_builder::gather_resources_callback) ../../src/devices/board/lib/acpi/device-builder.cc:84 <platform-bus-x86.so>+0x368278 gregkh#13 0x000021afcfbddb87 in acpi::Manager::configure_discovered_devices(acpi::Manager*) ../../src/devices/board/lib/acpi/manager.cc:75 <platform-bus-x86.so>+0x49db87 gregkh#14 0x000021afcf99091d in publish_acpi_devices(acpi::Manager*, zx_device_t*, zx_device_t*) ../../src/devices/board/drivers/x86/acpi-nswalk.cc:95 <platform-bus-x86.so>+0x25091d gregkh#15 0x000021afcf9c1d4e in x86::X86::do_init(x86::X86*) ../../src/devices/board/drivers/x86/x86.cc:60 <platform-bus-x86.so>+0x281d4e gregkh#16 0x000021afcf9e33ad in λ(x86::X86::ddk_init::(anon class)*) ../../src/devices/board/drivers/x86/x86.cc:77 <platform-bus-x86.so>+0x2a33ad gregkh#17 0x000021afcf9e313e in fit::internal::target<(lambda at../../src/devices/board/drivers/x86/x86.cc:76:19), false, false, std::__2::allocator<std::byte>, void>::invoke(void*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:183 <platform-bus-x86.so>+0x2a313e gregkh#18 0x000021afcfbab4c7 in fit::internal::function_base<16UL, false, void(), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <platform-bus-x86.so>+0x46b4c7 gregkh#19 0x000021afcfbab342 in fit::function_impl<16UL, false, void(), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/function.h:315 <platform-bus-x86.so>+0x46b342 gregkh#20 0x000021afcfcd98c3 in async::internal::retained_task::Handler(async_dispatcher_t*, async_task_t*, zx_status_t) ../../sdk/lib/async/task.cc:24 <platform-bus-x86.so>+0x5998c3 gregkh#21 0x00002290f9924616 in λ(const driver_runtime::Dispatcher::post_task::(anon class)*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/dispatcher.cc:789 <libdriver_runtime.so>+0x10a616 #22 0x00002290f9924323 in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:788:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int>::invoke(void*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0x10a323 #23 0x00002290f9904b76 in fit::internal::function_base<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xeab76 #24 0x00002290f9904831 in fit::callback_impl<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::operator()(fit::callback_impl<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/function.h:471 <libdriver_runtime.so>+0xea831 #25 0x00002290f98d5adc in driver_runtime::callback_request::Call(driver_runtime::callback_request*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/callback_request.h:74 <libdriver_runtime.so>+0xbbadc #26 0x00002290f98e1e58 in driver_runtime::Dispatcher::dispatch_callback(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >) ../../src/devices/bin/driver_runtime/dispatcher.cc:1248 <libdriver_runtime.so>+0xc7e58 #27 0x00002290f98e4159 in driver_runtime::Dispatcher::dispatch_callbacks(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:1308 <libdriver_runtime.so>+0xca159 #28 0x00002290f9918414 in λ(const driver_runtime::Dispatcher::create_with_adder::(anon class)*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:353 <libdriver_runtime.so>+0xfe414 #29 0x00002290f991812d in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:351:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>>::invoke(void*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0xfe12d #30 0x00002290f9906fc7 in fit::internal::function_base<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xecfc7 #31 0x00002290f9906c66 in fit::function_impl<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/function.h:315 <libdriver_runtime.so>+0xecc66 #32 0x00002290f98e73d9 in driver_runtime::Dispatcher::event_waiter::invoke_callback(driver_runtime::Dispatcher::event_waiter*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.h:543 <libdriver_runtime.so>+0xcd3d9 #33 0x00002290f98e700d in driver_runtime::Dispatcher::event_waiter::handle_event(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/dispatcher.cc:1442 <libdriver_runtime.so>+0xcd00d #34 0x00002290f9918983 in async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event(async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>*, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/async_loop_owned_event_handler.h:59 <libdriver_runtime.so>+0xfe983 #35 0x00002290f9918b9e in async::wait_method<async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>, &async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event>::call_handler(async_dispatcher_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async/include/lib/async/cpp/wait.h:201 <libdriver_runtime.so>+0xfeb9e #36 0x00002290f99bf509 in async_loop_dispatch_wait(async_loop_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async-loop/loop.c:394 <libdriver_runtime.so>+0x1a5509 #37 0x00002290f99b9958 in async_loop_run_once(async_loop_t*, zx_time_t) ../../sdk/lib/async-loop/loop.c:343 <libdriver_runtime.so>+0x19f958 #38 0x00002290f99b9247 in async_loop_run(async_loop_t*, zx_time_t, _Bool) ../../sdk/lib/async-loop/loop.c:301 <libdriver_runtime.so>+0x19f247 #39 0x00002290f99ba962 in async_loop_run_thread(void*) ../../sdk/lib/async-loop/loop.c:860 <libdriver_runtime.so>+0x1a0962 #40 0x000041afd176ef30 in start_c11(void*) ../../zircon/third_party/ulib/musl/pthread/pthread_create.c:63 <libc.so>+0x84f30 #41 0x000041afd18a448d in thread_trampoline(uintptr_t, uintptr_t) ../../zircon/system/ulib/runtime/thread.cc:100 <libc.so>+0x1ba48d Link: acpica/acpica@1c28da22 Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/4664267.LvFx2qVVIh@rjwysocki.net Signed-off-by: Tamir Duberstein <tamird@gmail.com> [ rjw: Pick up the tag from Tamir ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1e9ac33 ] Before the commit under the Fixes tag below, bnxt_ulp_stop() and bnxt_ulp_start() were always invoked in pairs. After that commit, the new bnxt_ulp_restart() can be invoked after bnxt_ulp_stop() has been called. This may result in the RoCE driver's aux driver .suspend() method being invoked twice. The 2nd bnxt_re_suspend() call will crash when it dereferences a NULL pointer: (NULL ib_device): Handle device suspend call BUG: kernel NULL pointer dereference, address: 0000000000000b78 PGD 0 P4D 0 Oops: Oops: 0000 [gregkh#1] SMP PTI CPU: 20 UID: 0 PID: 181 Comm: kworker/u96:5 Tainted: G S 6.15.0-rc1 gregkh#4 PREEMPT(voluntary) Tainted: [S]=CPU_OUT_OF_SPEC Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.4.3 01/17/2017 Workqueue: bnxt_pf_wq bnxt_sp_task [bnxt_en] RIP: 0010:bnxt_re_suspend+0x45/0x1f0 [bnxt_re] Code: 8b 05 a7 3c 5b f5 48 89 44 24 18 31 c0 49 8b 5c 24 08 4d 8b 2c 24 e8 ea 06 0a f4 48 c7 c6 04 60 52 c0 48 89 df e8 1b ce f9 ff <48> 8b 83 78 0b 00 00 48 8b 80 38 03 00 00 a8 40 0f 85 b5 00 00 00 RSP: 0018:ffffa2e84084fd88 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000001 RDX: 0000000000000000 RSI: ffffffffb4b6b934 RDI: 00000000ffffffff RBP: ffffa1760954c9c0 R08: 0000000000000000 R09: c0000000ffffdfff R10: 0000000000000001 R11: ffffa2e84084fb50 R12: ffffa176031ef070 R13: ffffa17609775000 R14: ffffa17603adc180 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffffa17daa397000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000b78 CR3: 00000004aaa30003 CR4: 00000000003706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> bnxt_ulp_stop+0x69/0x90 [bnxt_en] bnxt_sp_task+0x678/0x920 [bnxt_en] ? __schedule+0x514/0xf50 process_scheduled_works+0x9d/0x400 worker_thread+0x11c/0x260 ? __pfx_worker_thread+0x10/0x10 kthread+0xfe/0x1e0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2b/0x40 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 Check the BNXT_EN_FLAG_ULP_STOPPED flag and do not proceed if the flag is already set. This will preserve the original symmetrical bnxt_ulp_stop() and bnxt_ulp_start(). Also, inside bnxt_ulp_start(), clear the BNXT_EN_FLAG_ULP_STOPPED flag after taking the mutex to avoid any race condition. And for symmetry, only proceed in bnxt_ulp_start() if the BNXT_EN_FLAG_ULP_STOPPED is set. Fixes: 3c163f3 ("bnxt_en: Optimize recovery path ULP locking in the driver") Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Co-developed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250613231841.377988-2-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

pert script tests fails with segmentation fault as below: 92: perf script tests: --- start --- test child forked, pid 103769 DB test [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.012 MB /tmp/perf-test-script.7rbftEpOzX/perf.data (9 samples) ] /usr/libexec/perf-core/tests/shell/script.sh: line 35: 103780 Segmentation fault (core dumped) perf script -i "${perfdatafile}" -s "${db_test}" --- Cleaning up --- ---- end(-1) ---- 92: perf script tests : FAILED! Backtrace pointed to : #0 0x0000000010247dd0 in maps.machine () gregkh#1 0x00000000101d178c in db_export.sample () gregkh#2 0x00000000103412c8 in python_process_event () gregkh#3 0x000000001004eb28 in process_sample_event () gregkh#4 0x000000001024fcd0 in machines.deliver_event () gregkh#5 0x000000001025005c in perf_session.deliver_event () gregkh#6 0x00000000102568b0 in __ordered_events__flush.part.0 () gregkh#7 0x0000000010251618 in perf_session.process_events () gregkh#8 0x0000000010053620 in cmd_script () gregkh#9 0x00000000100b5a28 in run_builtin () gregkh#10 0x00000000100b5f94 in handle_internal_command () gregkh#11 0x0000000010011114 in main () Further investigation reveals that this occurs in the `perf script tests`, because it uses `db_test.py` script. This script sets `perf_db_export_mode = True`. With `perf_db_export_mode` enabled, if a sample originates from a hypervisor, perf doesn't set maps for "[H]" sample in the code. Consequently, `al->maps` remains NULL when `maps__machine(al->maps)` is called from `db_export__sample`. As al->maps can be NULL in case of Hypervisor samples , use thread->maps because even for Hypervisor sample, machine should exist. If we don't have machine for some reason, return -1 to avoid segmentation fault. Reported-by: Disha Goel <disgoel@linux.ibm.com> Signed-off-by: Aditya Bodkhe <aditya.b1@linux.ibm.com> Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Disha Goel <disgoel@linux.ibm.com> Link: https://lore.kernel.org/r/20250429065132.36839-1-adityab1@linux.ibm.com Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org>

Without the change `perf `hangs up on charaster devices. On my system it's enough to run system-wide sampler for a few seconds to get the hangup: $ perf record -a -g --call-graph=dwarf $ perf report # hung `strace` shows that hangup happens on reading on a character device `/dev/dri/renderD128` $ strace -y -f -p 2780484 strace: Process 2780484 attached pread64(101</dev/dri/renderD128>, strace: Process 2780484 detached It's call trace descends into `elfutils`: $ gdb -p 2780484 (gdb) bt #0 0x00007f5e508f04b7 in __libc_pread64 (fd=101, buf=0x7fff9df7edb0, count=0, offset=0) at ../sysdeps/unix/sysv/linux/pread64.c:25 gregkh#1 0x00007f5e52b79515 in read_file () from /<<NIX>>/elfutils-0.192/lib/libelf.so.1 gregkh#2 0x00007f5e52b25666 in libdw_open_elf () from /<<NIX>>/elfutils-0.192/lib/libdw.so.1 gregkh#3 0x00007f5e52b25907 in __libdw_open_file () from /<<NIX>>/elfutils-0.192/lib/libdw.so.1 gregkh#4 0x00007f5e52b120a9 in dwfl_report_elf@@ELFUTILS_0.156 () from /<<NIX>>/elfutils-0.192/lib/libdw.so.1 gregkh#5 0x000000000068bf20 in __report_module (al=al@entry=0x7fff9df80010, ip=ip@entry=139803237033216, ui=ui@entry=0x5369b5e0) at util/dso.h:537 gregkh#6 0x000000000068c3d1 in report_module (ip=139803237033216, ui=0x5369b5e0) at util/unwind-libdw.c:114 gregkh#7 frame_callback (state=0x535aef10, arg=0x5369b5e0) at util/unwind-libdw.c:242 gregkh#8 0x00007f5e52b261d3 in dwfl_thread_getframes () from /<<NIX>>/elfutils-0.192/lib/libdw.so.1 gregkh#9 0x00007f5e52b25bdb in get_one_thread_cb () from /<<NIX>>/elfutils-0.192/lib/libdw.so.1 gregkh#10 0x00007f5e52b25faa in dwfl_getthreads () from /<<NIX>>/elfutils-0.192/lib/libdw.so.1 gregkh#11 0x00007f5e52b26514 in dwfl_getthread_frames () from /<<NIX>>/elfutils-0.192/lib/libdw.so.1 gregkh#12 0x000000000068c6ce in unwind__get_entries (cb=cb@entry=0x5d4620 <unwind_entry>, arg=arg@entry=0x10cd5fa0, thread=thread@entry=0x1076a290, data=data@entry=0x7fff9df80540, max_stack=max_stack@entry=127, best_effort=best_effort@entry=false) at util/thread.h:152 gregkh#13 0x00000000005dae95 in thread__resolve_callchain_unwind (evsel=0x106006d0, thread=0x1076a290, cursor=0x10cd5fa0, sample=0x7fff9df80540, max_stack=127, symbols=true) at util/machine.c:2939 gregkh#14 thread__resolve_callchain_unwind (thread=0x1076a290, cursor=0x10cd5fa0, evsel=0x106006d0, sample=0x7fff9df80540, max_stack=127, symbols=true) at util/machine.c:2920 gregkh#15 __thread__resolve_callchain (thread=0x1076a290, cursor=0x10cd5fa0, evsel=0x106006d0, evsel@entry=0x7fff9df80440, sample=0x7fff9df80540, parent=parent@entry=0x7fff9df804a0, root_al=root_al@entry=0x7fff9df80440, max_stack=127, symbols=true) at util/machine.c:2970 gregkh#16 0x00000000005d0cb2 in thread__resolve_callchain (thread=<optimized out>, cursor=<optimized out>, evsel=0x7fff9df80440, sample=<optimized out>, parent=0x7fff9df804a0, root_al=0x7fff9df80440, max_stack=127) at util/machine.h:198 gregkh#17 sample__resolve_callchain (sample=<optimized out>, cursor=<optimized out>, parent=parent@entry=0x7fff9df804a0, evsel=evsel@entry=0x106006d0, al=al@entry=0x7fff9df80440, max_stack=max_stack@entry=127) at util/callchain.c:1127 gregkh#18 0x0000000000617e08 in hist_entry_iter__add (iter=iter@entry=0x7fff9df80480, al=al@entry=0x7fff9df80440, max_stack_depth=127, arg=arg@entry=0x7fff9df81ae0) at util/hist.c:1255 gregkh#19 0x000000000045d2d0 in process_sample_event (tool=0x7fff9df81ae0, event=<optimized out>, sample=0x7fff9df80540, evsel=0x106006d0, machine=<optimized out>) at builtin-report.c:334 gregkh#20 0x00000000005e3bb1 in perf_session__deliver_event (session=0x105ff2c0, event=0x7f5c7d735ca0, tool=0x7fff9df81ae0, file_offset=2914716832, file_path=0x105ffbf0 "perf.data") at util/session.c:1367 gregkh#21 0x00000000005e8d93 in do_flush (oe=0x105ffa50, show_progress=false) at util/ordered-events.c:245 #22 __ordered_events__flush (oe=0x105ffa50, how=OE_FLUSH__ROUND, timestamp=<optimized out>) at util/ordered-events.c:324 #23 0x00000000005e1f64 in perf_session__process_user_event (session=0x105ff2c0, event=0x7f5c7d752b18, file_offset=2914835224, file_path=0x105ffbf0 "perf.data") at util/session.c:1419 #24 0x00000000005e47c7 in reader__read_event (rd=rd@entry=0x7fff9df81260, session=session@entry=0x105ff2c0, --Type <RET> for more, q to quit, c to continue without paging-- quit prog=prog@entry=0x7fff9df81220) at util/session.c:2132 #25 0x00000000005e4b37 in reader__process_events (rd=0x7fff9df81260, session=0x105ff2c0, prog=0x7fff9df81220) at util/session.c:2181 #26 __perf_session__process_events (session=0x105ff2c0) at util/session.c:2226 #27 perf_session__process_events (session=session@entry=0x105ff2c0) at util/session.c:2390 #28 0x0000000000460add in __cmd_report (rep=0x7fff9df81ae0) at builtin-report.c:1076 #29 cmd_report (argc=<optimized out>, argv=<optimized out>) at builtin-report.c:1827 #30 0x00000000004c5a40 in run_builtin (p=p@entry=0xd8f7f8 <commands+312>, argc=argc@entry=1, argv=argv@entry=0x7fff9df844b0) at perf.c:351 #31 0x00000000004c5d63 in handle_internal_command (argc=argc@entry=1, argv=argv@entry=0x7fff9df844b0) at perf.c:404 #32 0x0000000000442de3 in run_argv (argcp=<synthetic pointer>, argv=<synthetic pointer>) at perf.c:448 #33 main (argc=<optimized out>, argv=0x7fff9df844b0) at perf.c:556 The hangup happens because nothing in` perf` or `elfutils` checks if a mapped file is easily readable. The change conservatively skips all non-regular files. Signed-off-by: Sergei Trofimovich <slyich@gmail.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20250505174419.2814857-1-slyich@gmail.com Signed-off-by: Namhyung Kim <namhyung@kernel.org>

Symbolize stack traces by creating a live machine. Add this functionality to dump_stack and switch dump_stack users to use it. Switch TUI to use it. Add stack traces to the child test function which can be useful to diagnose blocked code. Example output: ``` $ perf test -vv PERF_RECORD_ ... 7: PERF_RECORD_* events & perf_sample fields: 7: PERF_RECORD_* events & perf_sample fields : Running (1 active) ^C Signal (2) while running tests. Terminating tests with the same signal Internal test harness failure. Completing any started tests: : 7: PERF_RECORD_* events & perf_sample fields: ---- unexpected signal (2) ---- #0 0x55788c6210a3 in child_test_sig_handler builtin-test.c:0 gregkh#1 0x7fc12fe49df0 in __restore_rt libc_sigaction.c:0 gregkh#2 0x7fc12fe99687 in __internal_syscall_cancel cancellation.c:64 gregkh#3 0x7fc12fee5f7a in clock_nanosleep@GLIBC_2.2.5 clock_nanosleep.c:72 gregkh#4 0x7fc12fef1393 in __nanosleep nanosleep.c:26 gregkh#5 0x7fc12ff02d68 in __sleep sleep.c:55 gregkh#6 0x55788c63196b in test__PERF_RECORD perf-record.c:0 gregkh#7 0x55788c620fb0 in run_test_child builtin-test.c:0 gregkh#8 0x55788c5bd18d in start_command run-command.c:127 gregkh#9 0x55788c621ef3 in __cmd_test builtin-test.c:0 gregkh#10 0x55788c6225bf in cmd_test ??:0 gregkh#11 0x55788c5afbd0 in run_builtin perf.c:0 gregkh#12 0x55788c5afeeb in handle_internal_command perf.c:0 gregkh#13 0x55788c52b383 in main ??:0 gregkh#14 0x7fc12fe33ca8 in __libc_start_call_main libc_start_call_main.h:74 gregkh#15 0x7fc12fe33d65 in __libc_start_main@@GLIBC_2.34 libc-start.c:128 gregkh#16 0x55788c52b9d1 in _start ??:0 ---- unexpected signal (2) ---- #0 0x55788c6210a3 in child_test_sig_handler builtin-test.c:0 gregkh#1 0x7fc12fe49df0 in __restore_rt libc_sigaction.c:0 gregkh#2 0x7fc12fea3a14 in pthread_sigmask@GLIBC_2.2.5 pthread_sigmask.c:45 gregkh#3 0x7fc12fe49fd9 in __GI___sigprocmask sigprocmask.c:26 gregkh#4 0x7fc12ff2601b in __longjmp_chk longjmp.c:36 gregkh#5 0x55788c6210c0 in print_test_result.isra.0 builtin-test.c:0 gregkh#6 0x7fc12fe49df0 in __restore_rt libc_sigaction.c:0 gregkh#7 0x7fc12fe99687 in __internal_syscall_cancel cancellation.c:64 gregkh#8 0x7fc12fee5f7a in clock_nanosleep@GLIBC_2.2.5 clock_nanosleep.c:72 gregkh#9 0x7fc12fef1393 in __nanosleep nanosleep.c:26 gregkh#10 0x7fc12ff02d68 in __sleep sleep.c:55 gregkh#11 0x55788c63196b in test__PERF_RECORD perf-record.c:0 gregkh#12 0x55788c620fb0 in run_test_child builtin-test.c:0 gregkh#13 0x55788c5bd18d in start_command run-command.c:127 gregkh#14 0x55788c621ef3 in __cmd_test builtin-test.c:0 gregkh#15 0x55788c6225bf in cmd_test ??:0 gregkh#16 0x55788c5afbd0 in run_builtin perf.c:0 gregkh#17 0x55788c5afeeb in handle_internal_command perf.c:0 gregkh#18 0x55788c52b383 in main ??:0 gregkh#19 0x7fc12fe33ca8 in __libc_start_call_main libc_start_call_main.h:74 gregkh#20 0x7fc12fe33d65 in __libc_start_main@@GLIBC_2.34 libc-start.c:128 gregkh#21 0x55788c52b9d1 in _start ??:0 7: PERF_RECORD_* events & perf_sample fields : Skip (permissions) ``` Signed-off-by: Ian Rogers <irogers@google.com> Link: https://lore.kernel.org/r/20250624210500.2121303-1-irogers@google.com Signed-off-by: Namhyung Kim <namhyung@kernel.org>

Calling perf top with branch filters enabled on Intel CPU's with branch counters logging (A.K.A LBR event logging [1]) support results in a segfault. $ perf top -e '{cpu_core/cpu-cycles/,cpu_core/event=0xc6,umask=0x3,frontend=0x11,name=frontend_retired_dsb_miss/}' -j any,counter ... Thread 27 "perf" received signal SIGSEGV, Segmentation fault. [Switching to Thread 0x7fffafff76c0 (LWP 949003)] perf_env__find_br_cntr_info (env=0xf66dc0 <perf_env>, nr=0x0, width=0x7fffafff62c0) at util/env.c:653 653 *width = env->cpu_pmu_caps ? env->br_cntr_width : (gdb) bt #0 perf_env__find_br_cntr_info (env=0xf66dc0 <perf_env>, nr=0x0, width=0x7fffafff62c0) at util/env.c:653 gregkh#1 0x00000000005b1599 in symbol__account_br_cntr (branch=0x7fffcc3db580, evsel=0xfea2d0, offset=12, br_cntr=8) at util/annotate.c:345 gregkh#2 0x00000000005b17fb in symbol__account_cycles (addr=5658172, start=5658160, sym=0x7fffcc0ee420, cycles=539, evsel=0xfea2d0, br_cntr=8) at util/annotate.c:389 gregkh#3 0x00000000005b1976 in addr_map_symbol__account_cycles (ams=0x7fffcd7b01d0, start=0x7fffcd7b02b0, cycles=539, evsel=0xfea2d0, br_cntr=8) at util/annotate.c:422 gregkh#4 0x000000000068d57f in hist__account_cycles (bs=0x110d288, al=0x7fffafff6540, sample=0x7fffafff6760, nonany_branch_mode=false, total_cycles=0x0, evsel=0xfea2d0) at util/hist.c:2850 gregkh#5 0x0000000000446216 in hist_iter__top_callback (iter=0x7fffafff6590, al=0x7fffafff6540, single=true, arg=0x7fffffff9e00) at builtin-top.c:737 gregkh#6 0x0000000000689787 in hist_entry_iter__add (iter=0x7fffafff6590, al=0x7fffafff6540, max_stack_depth=127, arg=0x7fffffff9e00) at util/hist.c:1359 gregkh#7 0x0000000000446710 in perf_event__process_sample (tool=0x7fffffff9e00, event=0x110d250, evsel=0xfea2d0, sample=0x7fffafff6760, machine=0x108c968) at builtin-top.c:845 gregkh#8 0x0000000000447735 in deliver_event (qe=0x7fffffffa120, qevent=0x10fc200) at builtin-top.c:1211 gregkh#9 0x000000000064ccae in do_flush (oe=0x7fffffffa120, show_progress=false) at util/ordered-events.c:245 gregkh#10 0x000000000064d005 in __ordered_events__flush (oe=0x7fffffffa120, how=OE_FLUSH__TOP, timestamp=0) at util/ordered-events.c:324 gregkh#11 0x000000000064d0ef in ordered_events__flush (oe=0x7fffffffa120, how=OE_FLUSH__TOP) at util/ordered-events.c:342 gregkh#12 0x00000000004472a9 in process_thread (arg=0x7fffffff9e00) at builtin-top.c:1120 gregkh#13 0x00007ffff6e7dba8 in start_thread (arg=<optimized out>) at pthread_create.c:448 gregkh#14 0x00007ffff6f01b8c in __GI___clone3 () at ../sysdeps/unix/sysv/linux/x86_64/clone3.S:78 The cause is that perf_env__find_br_cntr_info tries to access a null pointer pmu_caps in the perf_env struct. A similar issue exists for homogeneous core systems which use the cpu_pmu_caps structure. Fix this by populating cpu_pmu_caps and pmu_caps structures with values from sysfs when calling perf top with branch stack sampling enabled. [1], LBR event logging introduced here: https://lore.kernel.org/all/20231025201626.3000228-5-kan.liang@linux.intel.com/ Reviewed-by: Ian Rogers <irogers@google.com> Signed-off-by: Thomas Falcon <thomas.falcon@intel.com> Link: https://lore.kernel.org/r/20250612163659.1357950-2-thomas.falcon@intel.com Signed-off-by: Namhyung Kim <namhyung@kernel.org>

commit f7fa852 upstream. Add the SM6115 MDSS compatible to clients compatible list, as it also needs that workaround. Without this workaround, for example, QRB4210 RB2 which is based on SM4250/SM6115 generates a lot of smmu unhandled context faults during boot: arm_smmu_context_fault: 116854 callbacks suppressed arm-smmu c600000.iommu: Unhandled context fault: fsr=0x402, iova=0x5c0ec600, fsynr=0x320021, cbfrsynra=0x420, cb=5 arm-smmu c600000.iommu: FSR = 00000402 [Format=2 TF], SID=0x420 arm-smmu c600000.iommu: FSYNR0 = 00320021 [S1CBNDX=50 PNU PLVL=1] arm-smmu c600000.iommu: Unhandled context fault: fsr=0x402, iova=0x5c0d7800, fsynr=0x320021, cbfrsynra=0x420, cb=5 arm-smmu c600000.iommu: FSR = 00000402 [Format=2 TF], SID=0x420 and also failed initialisation of lontium lt9611uxc, gpu and dpu is observed: (binding MDSS components triggered by lt9611uxc have failed) ------------[ cut here ]------------ !aspace WARNING: CPU: 6 PID: 324 at drivers/gpu/drm/msm/msm_gem_vma.c:130 msm_gem_vma_init+0x150/0x18c [msm] Modules linked in: ... (long list of modules) CPU: 6 UID: 0 PID: 324 Comm: (udev-worker) Not tainted 6.15.0-03037-gaacc73ceeb8b gregkh#4 PREEMPT Hardware name: Qualcomm Technologies, Inc. QRB4210 RB2 (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : msm_gem_vma_init+0x150/0x18c [msm] lr : msm_gem_vma_init+0x150/0x18c [msm] sp : ffff80008144b280 ... Call trace: msm_gem_vma_init+0x150/0x18c [msm] (P) get_vma_locked+0xc0/0x194 [msm] msm_gem_get_and_pin_iova_range+0x4c/0xdc [msm] msm_gem_kernel_new+0x48/0x160 [msm] msm_gpu_init+0x34c/0x53c [msm] adreno_gpu_init+0x1b0/0x2d8 [msm] a6xx_gpu_init+0x1e8/0x9e0 [msm] adreno_bind+0x2b8/0x348 [msm] component_bind_all+0x100/0x230 msm_drm_bind+0x13c/0x3d0 [msm] try_to_bring_up_aggregate_device+0x164/0x1d0 __component_add+0xa4/0x174 component_add+0x14/0x20 dsi_dev_attach+0x20/0x34 [msm] dsi_host_attach+0x58/0x98 [msm] devm_mipi_dsi_attach+0x34/0x90 lt9611uxc_attach_dsi.isra.0+0x94/0x124 [lontium_lt9611uxc] lt9611uxc_probe+0x540/0x5fc [lontium_lt9611uxc] i2c_device_probe+0x148/0x2a8 really_probe+0xbc/0x2c0 __driver_probe_device+0x78/0x120 driver_probe_device+0x3c/0x154 __driver_attach+0x90/0x1a0 bus_for_each_dev+0x68/0xb8 driver_attach+0x24/0x30 bus_add_driver+0xe4/0x208 driver_register+0x68/0x124 i2c_register_driver+0x48/0xcc lt9611uxc_driver_init+0x20/0x1000 [lontium_lt9611uxc] do_one_initcall+0x60/0x1d4 do_init_module+0x54/0x1fc load_module+0x1748/0x1c8c init_module_from_file+0x74/0xa0 __arm64_sys_finit_module+0x130/0x2f8 invoke_syscall+0x48/0x104 el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x2c/0x80 el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c ---[ end trace 0000000000000000 ]--- msm_dpu 5e01000.display-controller: [drm:msm_gpu_init [msm]] *ERROR* could not allocate memptrs: -22 msm_dpu 5e01000.display-controller: failed to load adreno gpu platform a400000.remoteproc:glink-edge:apr:service@7:dais: Adding to iommu group 19 msm_dpu 5e01000.display-controller: failed to bind 5900000.gpu (ops a3xx_ops [msm]): -22 msm_dpu 5e01000.display-controller: adev bind failed: -22 lt9611uxc 0-002b: failed to attach dsi to host lt9611uxc 0-002b: probe with driver lt9611uxc failed with error -22 Suggested-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Fixes: 3581b70 ("drm/msm/disp/dpu1: add support for display on SM6115") Cc: stable@vger.kernel.org Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> Link: https://lore.kernel.org/r/20250613173238.15061-1-alexey.klimov@linaro.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f7fa852 upstream. Add the SM6115 MDSS compatible to clients compatible list, as it also needs that workaround. Without this workaround, for example, QRB4210 RB2 which is based on SM4250/SM6115 generates a lot of smmu unhandled context faults during boot: arm_smmu_context_fault: 116854 callbacks suppressed arm-smmu c600000.iommu: Unhandled context fault: fsr=0x402, iova=0x5c0ec600, fsynr=0x320021, cbfrsynra=0x420, cb=5 arm-smmu c600000.iommu: FSR = 00000402 [Format=2 TF], SID=0x420 arm-smmu c600000.iommu: FSYNR0 = 00320021 [S1CBNDX=50 PNU PLVL=1] arm-smmu c600000.iommu: Unhandled context fault: fsr=0x402, iova=0x5c0d7800, fsynr=0x320021, cbfrsynra=0x420, cb=5 arm-smmu c600000.iommu: FSR = 00000402 [Format=2 TF], SID=0x420 and also failed initialisation of lontium lt9611uxc, gpu and dpu is observed: (binding MDSS components triggered by lt9611uxc have failed) ------------[ cut here ]------------ !aspace WARNING: CPU: 6 PID: 324 at drivers/gpu/drm/msm/msm_gem_vma.c:130 msm_gem_vma_init+0x150/0x18c [msm] Modules linked in: ... (long list of modules) CPU: 6 UID: 0 PID: 324 Comm: (udev-worker) Not tainted 6.15.0-03037-gaacc73ceeb8b #4 PREEMPT Hardware name: Qualcomm Technologies, Inc. QRB4210 RB2 (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : msm_gem_vma_init+0x150/0x18c [msm] lr : msm_gem_vma_init+0x150/0x18c [msm] sp : ffff80008144b280 ... Call trace: msm_gem_vma_init+0x150/0x18c [msm] (P) get_vma_locked+0xc0/0x194 [msm] msm_gem_get_and_pin_iova_range+0x4c/0xdc [msm] msm_gem_kernel_new+0x48/0x160 [msm] msm_gpu_init+0x34c/0x53c [msm] adreno_gpu_init+0x1b0/0x2d8 [msm] a6xx_gpu_init+0x1e8/0x9e0 [msm] adreno_bind+0x2b8/0x348 [msm] component_bind_all+0x100/0x230 msm_drm_bind+0x13c/0x3d0 [msm] try_to_bring_up_aggregate_device+0x164/0x1d0 __component_add+0xa4/0x174 component_add+0x14/0x20 dsi_dev_attach+0x20/0x34 [msm] dsi_host_attach+0x58/0x98 [msm] devm_mipi_dsi_attach+0x34/0x90 lt9611uxc_attach_dsi.isra.0+0x94/0x124 [lontium_lt9611uxc] lt9611uxc_probe+0x540/0x5fc [lontium_lt9611uxc] i2c_device_probe+0x148/0x2a8 really_probe+0xbc/0x2c0 __driver_probe_device+0x78/0x120 driver_probe_device+0x3c/0x154 __driver_attach+0x90/0x1a0 bus_for_each_dev+0x68/0xb8 driver_attach+0x24/0x30 bus_add_driver+0xe4/0x208 driver_register+0x68/0x124 i2c_register_driver+0x48/0xcc lt9611uxc_driver_init+0x20/0x1000 [lontium_lt9611uxc] do_one_initcall+0x60/0x1d4 do_init_module+0x54/0x1fc load_module+0x1748/0x1c8c init_module_from_file+0x74/0xa0 __arm64_sys_finit_module+0x130/0x2f8 invoke_syscall+0x48/0x104 el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x2c/0x80 el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c ---[ end trace 0000000000000000 ]--- msm_dpu 5e01000.display-controller: [drm:msm_gpu_init [msm]] *ERROR* could not allocate memptrs: -22 msm_dpu 5e01000.display-controller: failed to load adreno gpu platform a400000.remoteproc:glink-edge:apr:service@7:dais: Adding to iommu group 19 msm_dpu 5e01000.display-controller: failed to bind 5900000.gpu (ops a3xx_ops [msm]): -22 msm_dpu 5e01000.display-controller: adev bind failed: -22 lt9611uxc 0-002b: failed to attach dsi to host lt9611uxc 0-002b: probe with driver lt9611uxc failed with error -22 Suggested-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Fixes: 3581b70 ("drm/msm/disp/dpu1: add support for display on SM6115") Cc: stable@vger.kernel.org Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> Link: https://lore.kernel.org/r/20250613173238.15061-1-alexey.klimov@linaro.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

BPF CI testing report a UAF issue: [ 16.446633] BUG: kernel NULL pointer dereference, address: 000000000000003 0 [ 16.447134] #PF: supervisor read access in kernel mod e [ 16.447516] #PF: error_code(0x0000) - not-present pag e [ 16.447878] PGD 0 P4D 0 [ 16.448063] Oops: Oops: 0000 [gregkh#1] PREEMPT SMP NOPT I [ 16.448409] CPU: 0 UID: 0 PID: 9 Comm: kworker/0:1 Tainted: G OE 6.13.0-rc3-g89e8a75fda73-dirty gregkh#4 2 [ 16.449124] Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODUL E [ 16.449502] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/201 4 [ 16.450201] Workqueue: smc_hs_wq smc_listen_wor k [ 16.450531] RIP: 0010:smc_listen_work+0xc02/0x159 0 [ 16.452158] RSP: 0018:ffffb5ab40053d98 EFLAGS: 0001024 6 [ 16.452526] RAX: 0000000000000001 RBX: 0000000000000002 RCX: 000000000000030 0 [ 16.452994] RDX: 0000000000000280 RSI: 00003513840053f0 RDI: 000000000000000 0 [ 16.453492] RBP: ffffa097808e3800 R08: ffffa09782dba1e0 R09: 000000000000000 5 [ 16.453987] R10: 0000000000000000 R11: 0000000000000000 R12: ffffa0978274640 0 [ 16.454497] R13: 0000000000000000 R14: 0000000000000000 R15: ffffa09782d4092 0 [ 16.454996] FS: 0000000000000000(0000) GS:ffffa097bbc00000(0000) knlGS:000000000000000 0 [ 16.455557] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003 3 [ 16.455961] CR2: 0000000000000030 CR3: 0000000102788004 CR4: 0000000000770ef 0 [ 16.456459] PKRU: 5555555 4 [ 16.456654] Call Trace : [ 16.456832] <TASK > [ 16.456989] ? __die+0x23/0x7 0 [ 16.457215] ? page_fault_oops+0x180/0x4c 0 [ 16.457508] ? __lock_acquire+0x3e6/0x249 0 [ 16.457801] ? exc_page_fault+0x68/0x20 0 [ 16.458080] ? asm_exc_page_fault+0x26/0x3 0 [ 16.458389] ? smc_listen_work+0xc02/0x159 0 [ 16.458689] ? smc_listen_work+0xc02/0x159 0 [ 16.458987] ? lock_is_held_type+0x8f/0x10 0 [ 16.459284] process_one_work+0x1ea/0x6d 0 [ 16.459570] worker_thread+0x1c3/0x38 0 [ 16.459839] ? __pfx_worker_thread+0x10/0x1 0 [ 16.460144] kthread+0xe0/0x11 0 [ 16.460372] ? __pfx_kthread+0x10/0x1 0 [ 16.460640] ret_from_fork+0x31/0x5 0 [ 16.460896] ? __pfx_kthread+0x10/0x1 0 [ 16.461166] ret_from_fork_asm+0x1a/0x3 0 [ 16.461453] </TASK > [ 16.461616] Modules linked in: bpf_testmod(OE) [last unloaded: bpf_testmod(OE) ] [ 16.462134] CR2: 000000000000003 0 [ 16.462380] ---[ end trace 0000000000000000 ]--- [ 16.462710] RIP: 0010:smc_listen_work+0xc02/0x1590 The direct cause of this issue is that after smc_listen_out_connected(), newclcsock->sk may be NULL since it will releases the smcsk. Therefore, if the application closes the socket immediately after accept, newclcsock->sk can be NULL. A possible execution order could be as follows: smc_listen_work | userspace ----------------------------------------------------------------- lock_sock(sk) | smc_listen_out_connected() | | \- smc_listen_out | | | \- release_sock | | |- sk->sk_data_ready() | | fd = accept(); | close(fd); | \- socket->sk = NULL; /* newclcsock->sk is NULL now */ SMC_STAT_SERV_SUCC_INC(sock_net(newclcsock->sk)) Since smc_listen_out_connected() will not fail, simply swapping the order of the code can easily fix this issue. Fixes: 3b2dec2 ("net/smc: restructure client and server code in af_smc") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Dust Li <dust.li@linux.alibaba.com> Link: https://patch.msgid.link/20250818054618.41615-1-alibuda@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

commit 0bef512 upstream. Based on a syzbot report, it appears many virtual drivers do not yet use netdev_lockdep_set_classes(), triggerring lockdep false positives. WARNING: possible recursive locking detected 6.8.0-rc4-next-20240212-syzkaller #0 Not tainted syz-executor.0/19016 is trying to acquire lock: ffff8880162cb298 (_xmit_ETHER#2){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff8880162cb298 (_xmit_ETHER#2){+.-.}-{2:2}, at: __netif_tx_lock include/linux/netdevice.h:4452 [inline] ffff8880162cb298 (_xmit_ETHER#2){+.-.}-{2:2}, at: sch_direct_xmit+0x1c4/0x5f0 net/sched/sch_generic.c:340 but task is already holding lock: ffff8880223db4d8 (_xmit_ETHER#2){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] ffff8880223db4d8 (_xmit_ETHER#2){+.-.}-{2:2}, at: __netif_tx_lock include/linux/netdevice.h:4452 [inline] ffff8880223db4d8 (_xmit_ETHER#2){+.-.}-{2:2}, at: sch_direct_xmit+0x1c4/0x5f0 net/sched/sch_generic.c:340 other info that might help us debug this: Possible unsafe locking scenario: CPU0 lock(_xmit_ETHER#2); lock(_xmit_ETHER#2); *** DEADLOCK *** May be due to missing lock nesting notation 9 locks held by syz-executor.0/19016: #0: ffffffff8f385208 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock net/core/rtnetlink.c:79 [inline] #0: ffffffff8f385208 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x82c/0x1040 net/core/rtnetlink.c:6603 gregkh#1: ffffc90000a08c00 ((&in_dev->mr_ifc_timer)){+.-.}-{0:0}, at: call_timer_fn+0xc0/0x600 kernel/time/timer.c:1697 gregkh#2: ffffffff8e131520 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:298 [inline] gregkh#2: ffffffff8e131520 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:750 [inline] gregkh#2: ffffffff8e131520 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x45f/0x1360 net/ipv4/ip_output.c:228 gregkh#3: ffffffff8e131580 (rcu_read_lock_bh){....}-{1:2}, at: local_bh_disable include/linux/bottom_half.h:20 [inline] gregkh#3: ffffffff8e131580 (rcu_read_lock_bh){....}-{1:2}, at: rcu_read_lock_bh include/linux/rcupdate.h:802 [inline] gregkh#3: ffffffff8e131580 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x2c4/0x3b10 net/core/dev.c:4284 gregkh#4: ffff8880416e3258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: spin_trylock include/linux/spinlock.h:361 [inline] gregkh#4: ffff8880416e3258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: qdisc_run_begin include/net/sch_generic.h:195 [inline] gregkh#4: ffff8880416e3258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: __dev_xmit_skb net/core/dev.c:3771 [inline] gregkh#4: ffff8880416e3258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: __dev_queue_xmit+0x1262/0x3b10 net/core/dev.c:4325 gregkh#5: ffff8880223db4d8 (_xmit_ETHER#2){+.-.}-{2:2}, at: spin_lock include/linux/spinlock.h:351 [inline] gregkh#5: ffff8880223db4d8 (_xmit_ETHER#2){+.-.}-{2:2}, at: __netif_tx_lock include/linux/netdevice.h:4452 [inline] gregkh#5: ffff8880223db4d8 (_xmit_ETHER#2){+.-.}-{2:2}, at: sch_direct_xmit+0x1c4/0x5f0 net/sched/sch_generic.c:340 gregkh#6: ffffffff8e131520 (rcu_read_lock){....}-{1:2}, at: rcu_lock_acquire include/linux/rcupdate.h:298 [inline] gregkh#6: ffffffff8e131520 (rcu_read_lock){....}-{1:2}, at: rcu_read_lock include/linux/rcupdate.h:750 [inline] gregkh#6: ffffffff8e131520 (rcu_read_lock){....}-{1:2}, at: ip_finish_output2+0x45f/0x1360 net/ipv4/ip_output.c:228 gregkh#7: ffffffff8e131580 (rcu_read_lock_bh){....}-{1:2}, at: local_bh_disable include/linux/bottom_half.h:20 [inline] gregkh#7: ffffffff8e131580 (rcu_read_lock_bh){....}-{1:2}, at: rcu_read_lock_bh include/linux/rcupdate.h:802 [inline] gregkh#7: ffffffff8e131580 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x2c4/0x3b10 net/core/dev.c:4284 gregkh#8: ffff888014d9d258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: spin_trylock include/linux/spinlock.h:361 [inline] gregkh#8: ffff888014d9d258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: qdisc_run_begin include/net/sch_generic.h:195 [inline] gregkh#8: ffff888014d9d258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: __dev_xmit_skb net/core/dev.c:3771 [inline] gregkh#8: ffff888014d9d258 (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+...}-{2:2}, at: __dev_queue_xmit+0x1262/0x3b10 net/core/dev.c:4325 stack backtrace: CPU: 1 PID: 19016 Comm: syz-executor.0 Not tainted 6.8.0-rc4-next-20240212-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114 check_deadlock kernel/locking/lockdep.c:3062 [inline] validate_chain+0x15c1/0x58e0 kernel/locking/lockdep.c:3856 __lock_acquire+0x1346/0x1fd0 kernel/locking/lockdep.c:5137 lock_acquire+0x1e4/0x530 kernel/locking/lockdep.c:5754 __raw_spin_lock include/linux/spinlock_api_smp.h:133 [inline] _raw_spin_lock+0x2e/0x40 kernel/locking/spinlock.c:154 spin_lock include/linux/spinlock.h:351 [inline] __netif_tx_lock include/linux/netdevice.h:4452 [inline] sch_direct_xmit+0x1c4/0x5f0 net/sched/sch_generic.c:340 __dev_xmit_skb net/core/dev.c:3784 [inline] __dev_queue_xmit+0x1912/0x3b10 net/core/dev.c:4325 neigh_output include/net/neighbour.h:542 [inline] ip_finish_output2+0xe66/0x1360 net/ipv4/ip_output.c:235 iptunnel_xmit+0x540/0x9b0 net/ipv4/ip_tunnel_core.c:82 ip_tunnel_xmit+0x20ee/0x2960 net/ipv4/ip_tunnel.c:831 erspan_xmit+0x9de/0x1460 net/ipv4/ip_gre.c:720 __netdev_start_xmit include/linux/netdevice.h:4989 [inline] netdev_start_xmit include/linux/netdevice.h:5003 [inline] xmit_one net/core/dev.c:3555 [inline] dev_hard_start_xmit+0x242/0x770 net/core/dev.c:3571 sch_direct_xmit+0x2b6/0x5f0 net/sched/sch_generic.c:342 __dev_xmit_skb net/core/dev.c:3784 [inline] __dev_queue_xmit+0x1912/0x3b10 net/core/dev.c:4325 neigh_output include/net/neighbour.h:542 [inline] ip_finish_output2+0xe66/0x1360 net/ipv4/ip_output.c:235 igmpv3_send_cr net/ipv4/igmp.c:723 [inline] igmp_ifc_timer_expire+0xb71/0xd90 net/ipv4/igmp.c:813 call_timer_fn+0x17e/0x600 kernel/time/timer.c:1700 expire_timers kernel/time/timer.c:1751 [inline] __run_timers+0x621/0x830 kernel/time/timer.c:2038 run_timer_softirq+0x67/0xf0 kernel/time/timer.c:2051 __do_softirq+0x2bc/0x943 kernel/softirq.c:554 invoke_softirq kernel/softirq.c:428 [inline] __irq_exit_rcu+0xf2/0x1c0 kernel/softirq.c:633 irq_exit_rcu+0x9/0x30 kernel/softirq.c:645 instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1076 [inline] sysvec_apic_timer_interrupt+0xa6/0xc0 arch/x86/kernel/apic/apic.c:1076 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x1a/0x20 arch/x86/include/asm/idtentry.h:702 RIP: 0010:resched_offsets_ok kernel/sched/core.c:10127 [inline] RIP: 0010:__might_resched+0x16f/0x780 kernel/sched/core.c:10142 Code: 00 4c 89 e8 48 c1 e8 03 48 ba 00 00 00 00 00 fc ff df 48 89 44 24 38 0f b6 04 10 84 c0 0f 85 87 04 00 00 41 8b 45 00 c1 e0 08 <01> d8 44 39 e0 0f 85 d6 00 00 00 44 89 64 24 1c 48 8d bc 24 a0 00 RSP: 0018:ffffc9000ee069e0 EFLAGS: 00000246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff8880296a9e00 RDX: dffffc0000000000 RSI: ffff8880296a9e00 RDI: ffffffff8bfe8fa0 RBP: ffffc9000ee06b00 R08: ffffffff82326877 R09: 1ffff11002b5ad1b R10: dffffc0000000000 R11: ffffed1002b5ad1c R12: 0000000000000000 R13: ffff8880296aa23c R14: 000000000000062a R15: 1ffff92001dc0d44 down_write+0x19/0x50 kernel/locking/rwsem.c:1578 kernfs_activate fs/kernfs/dir.c:1403 [inline] kernfs_add_one+0x4af/0x8b0 fs/kernfs/dir.c:819 __kernfs_create_file+0x22e/0x2e0 fs/kernfs/file.c:1056 sysfs_add_file_mode_ns+0x24a/0x310 fs/sysfs/file.c:307 create_files fs/sysfs/group.c:64 [inline] internal_create_group+0x4f4/0xf20 fs/sysfs/group.c:152 internal_create_groups fs/sysfs/group.c:192 [inline] sysfs_create_groups+0x56/0x120 fs/sysfs/group.c:218 create_dir lib/kobject.c:78 [inline] kobject_add_internal+0x472/0x8d0 lib/kobject.c:240 kobject_add_varg lib/kobject.c:374 [inline] kobject_init_and_add+0x124/0x190 lib/kobject.c:457 netdev_queue_add_kobject net/core/net-sysfs.c:1706 [inline] netdev_queue_update_kobjects+0x1f3/0x480 net/core/net-sysfs.c:1758 register_queue_kobjects net/core/net-sysfs.c:1819 [inline] netdev_register_kobject+0x265/0x310 net/core/net-sysfs.c:2059 register_netdevice+0x1191/0x19c0 net/core/dev.c:10298 bond_newlink+0x3b/0x90 drivers/net/bonding/bond_netlink.c:576 rtnl_newlink_create net/core/rtnetlink.c:3506 [inline] __rtnl_newlink net/core/rtnetlink.c:3726 [inline] rtnl_newlink+0x158f/0x20a0 net/core/rtnetlink.c:3739 rtnetlink_rcv_msg+0x885/0x1040 net/core/rtnetlink.c:6606 netlink_rcv_skb+0x1e3/0x430 net/netlink/af_netlink.c:2543 netlink_unicast_kernel net/netlink/af_netlink.c:1341 [inline] netlink_unicast+0x7ea/0x980 net/netlink/af_netlink.c:1367 netlink_sendmsg+0xa3c/0xd70 net/netlink/af_netlink.c:1908 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:745 __sys_sendto+0x3a4/0x4f0 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0xde/0x100 net/socket.c:2199 do_syscall_64+0xfb/0x240 entry_SYSCALL_64_after_hwframe+0x6d/0x75 RIP: 0033:0x7fc3fa87fa9c Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20240212140700.2795436-4-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sumanth Gavini <sumanth.gavini@yahoo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f7fa852 upstream. Add the SM6115 MDSS compatible to clients compatible list, as it also needs that workaround. Without this workaround, for example, QRB4210 RB2 which is based on SM4250/SM6115 generates a lot of smmu unhandled context faults during boot: arm_smmu_context_fault: 116854 callbacks suppressed arm-smmu c600000.iommu: Unhandled context fault: fsr=0x402, iova=0x5c0ec600, fsynr=0x320021, cbfrsynra=0x420, cb=5 arm-smmu c600000.iommu: FSR = 00000402 [Format=2 TF], SID=0x420 arm-smmu c600000.iommu: FSYNR0 = 00320021 [S1CBNDX=50 PNU PLVL=1] arm-smmu c600000.iommu: Unhandled context fault: fsr=0x402, iova=0x5c0d7800, fsynr=0x320021, cbfrsynra=0x420, cb=5 arm-smmu c600000.iommu: FSR = 00000402 [Format=2 TF], SID=0x420 and also failed initialisation of lontium lt9611uxc, gpu and dpu is observed: (binding MDSS components triggered by lt9611uxc have failed) ------------[ cut here ]------------ !aspace WARNING: CPU: 6 PID: 324 at drivers/gpu/drm/msm/msm_gem_vma.c:130 msm_gem_vma_init+0x150/0x18c [msm] Modules linked in: ... (long list of modules) CPU: 6 UID: 0 PID: 324 Comm: (udev-worker) Not tainted 6.15.0-03037-gaacc73ceeb8b gregkh#4 PREEMPT Hardware name: Qualcomm Technologies, Inc. QRB4210 RB2 (DT) pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : msm_gem_vma_init+0x150/0x18c [msm] lr : msm_gem_vma_init+0x150/0x18c [msm] sp : ffff80008144b280 ... Call trace: msm_gem_vma_init+0x150/0x18c [msm] (P) get_vma_locked+0xc0/0x194 [msm] msm_gem_get_and_pin_iova_range+0x4c/0xdc [msm] msm_gem_kernel_new+0x48/0x160 [msm] msm_gpu_init+0x34c/0x53c [msm] adreno_gpu_init+0x1b0/0x2d8 [msm] a6xx_gpu_init+0x1e8/0x9e0 [msm] adreno_bind+0x2b8/0x348 [msm] component_bind_all+0x100/0x230 msm_drm_bind+0x13c/0x3d0 [msm] try_to_bring_up_aggregate_device+0x164/0x1d0 __component_add+0xa4/0x174 component_add+0x14/0x20 dsi_dev_attach+0x20/0x34 [msm] dsi_host_attach+0x58/0x98 [msm] devm_mipi_dsi_attach+0x34/0x90 lt9611uxc_attach_dsi.isra.0+0x94/0x124 [lontium_lt9611uxc] lt9611uxc_probe+0x540/0x5fc [lontium_lt9611uxc] i2c_device_probe+0x148/0x2a8 really_probe+0xbc/0x2c0 __driver_probe_device+0x78/0x120 driver_probe_device+0x3c/0x154 __driver_attach+0x90/0x1a0 bus_for_each_dev+0x68/0xb8 driver_attach+0x24/0x30 bus_add_driver+0xe4/0x208 driver_register+0x68/0x124 i2c_register_driver+0x48/0xcc lt9611uxc_driver_init+0x20/0x1000 [lontium_lt9611uxc] do_one_initcall+0x60/0x1d4 do_init_module+0x54/0x1fc load_module+0x1748/0x1c8c init_module_from_file+0x74/0xa0 __arm64_sys_finit_module+0x130/0x2f8 invoke_syscall+0x48/0x104 el0_svc_common.constprop.0+0xc0/0xe0 do_el0_svc+0x1c/0x28 el0_svc+0x2c/0x80 el0t_64_sync_handler+0x10c/0x138 el0t_64_sync+0x198/0x19c ---[ end trace 0000000000000000 ]--- msm_dpu 5e01000.display-controller: [drm:msm_gpu_init [msm]] *ERROR* could not allocate memptrs: -22 msm_dpu 5e01000.display-controller: failed to load adreno gpu platform a400000.remoteproc:glink-edge:apr:service@7:dais: Adding to iommu group 19 msm_dpu 5e01000.display-controller: failed to bind 5900000.gpu (ops a3xx_ops [msm]): -22 msm_dpu 5e01000.display-controller: adev bind failed: -22 lt9611uxc 0-002b: failed to attach dsi to host lt9611uxc 0-002b: probe with driver lt9611uxc failed with error -22 Suggested-by: Bjorn Andersson <andersson@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Fixes: 3581b70 ("drm/msm/disp/dpu1: add support for display on SM6115") Cc: stable@vger.kernel.org Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> Link: https://lore.kernel.org/r/20250613173238.15061-1-alexey.klimov@linaro.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d9cef55 ] BPF CI testing report a UAF issue: [ 16.446633] BUG: kernel NULL pointer dereference, address: 000000000000003 0 [ 16.447134] #PF: supervisor read access in kernel mod e [ 16.447516] #PF: error_code(0x0000) - not-present pag e [ 16.447878] PGD 0 P4D 0 [ 16.448063] Oops: Oops: 0000 [gregkh#1] PREEMPT SMP NOPT I [ 16.448409] CPU: 0 UID: 0 PID: 9 Comm: kworker/0:1 Tainted: G OE 6.13.0-rc3-g89e8a75fda73-dirty gregkh#4 2 [ 16.449124] Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODUL E [ 16.449502] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/201 4 [ 16.450201] Workqueue: smc_hs_wq smc_listen_wor k [ 16.450531] RIP: 0010:smc_listen_work+0xc02/0x159 0 [ 16.452158] RSP: 0018:ffffb5ab40053d98 EFLAGS: 0001024 6 [ 16.452526] RAX: 0000000000000001 RBX: 0000000000000002 RCX: 000000000000030 0 [ 16.452994] RDX: 0000000000000280 RSI: 00003513840053f0 RDI: 000000000000000 0 [ 16.453492] RBP: ffffa097808e3800 R08: ffffa09782dba1e0 R09: 000000000000000 5 [ 16.453987] R10: 0000000000000000 R11: 0000000000000000 R12: ffffa0978274640 0 [ 16.454497] R13: 0000000000000000 R14: 0000000000000000 R15: ffffa09782d4092 0 [ 16.454996] FS: 0000000000000000(0000) GS:ffffa097bbc00000(0000) knlGS:000000000000000 0 [ 16.455557] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003 3 [ 16.455961] CR2: 0000000000000030 CR3: 0000000102788004 CR4: 0000000000770ef 0 [ 16.456459] PKRU: 5555555 4 [ 16.456654] Call Trace : [ 16.456832] <TASK > [ 16.456989] ? __die+0x23/0x7 0 [ 16.457215] ? page_fault_oops+0x180/0x4c 0 [ 16.457508] ? __lock_acquire+0x3e6/0x249 0 [ 16.457801] ? exc_page_fault+0x68/0x20 0 [ 16.458080] ? asm_exc_page_fault+0x26/0x3 0 [ 16.458389] ? smc_listen_work+0xc02/0x159 0 [ 16.458689] ? smc_listen_work+0xc02/0x159 0 [ 16.458987] ? lock_is_held_type+0x8f/0x10 0 [ 16.459284] process_one_work+0x1ea/0x6d 0 [ 16.459570] worker_thread+0x1c3/0x38 0 [ 16.459839] ? __pfx_worker_thread+0x10/0x1 0 [ 16.460144] kthread+0xe0/0x11 0 [ 16.460372] ? __pfx_kthread+0x10/0x1 0 [ 16.460640] ret_from_fork+0x31/0x5 0 [ 16.460896] ? __pfx_kthread+0x10/0x1 0 [ 16.461166] ret_from_fork_asm+0x1a/0x3 0 [ 16.461453] </TASK > [ 16.461616] Modules linked in: bpf_testmod(OE) [last unloaded: bpf_testmod(OE) ] [ 16.462134] CR2: 000000000000003 0 [ 16.462380] ---[ end trace 0000000000000000 ]--- [ 16.462710] RIP: 0010:smc_listen_work+0xc02/0x1590 The direct cause of this issue is that after smc_listen_out_connected(), newclcsock->sk may be NULL since it will releases the smcsk. Therefore, if the application closes the socket immediately after accept, newclcsock->sk can be NULL. A possible execution order could be as follows: smc_listen_work | userspace ----------------------------------------------------------------- lock_sock(sk) | smc_listen_out_connected() | | \- smc_listen_out | | | \- release_sock | | |- sk->sk_data_ready() | | fd = accept(); | close(fd); | \- socket->sk = NULL; /* newclcsock->sk is NULL now */ SMC_STAT_SERV_SUCC_INC(sock_net(newclcsock->sk)) Since smc_listen_out_connected() will not fail, simply swapping the order of the code can easily fix this issue. Fixes: 3b2dec2 ("net/smc: restructure client and server code in af_smc") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Dust Li <dust.li@linux.alibaba.com> Link: https://patch.msgid.link/20250818054618.41615-1-alibuda@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit f02c41f upstream. Use raw_spinlock in order to fix spurious messages about invalid context when spinlock debugging is enabled. The lock is only used to serialize register access. [ 4.239592] ============================= [ 4.239595] [ BUG: Invalid wait context ] [ 4.239599] 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 Not tainted [ 4.239603] ----------------------------- [ 4.239606] kworker/u8:5/76 is trying to lock: [ 4.239609] ffff0000091898a0 (&p->lock){....}-{3:3}, at: gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.239641] other info that might help us debug this: [ 4.239643] context-{5:5} [ 4.239646] 5 locks held by kworker/u8:5/76: [ 4.239651] #0: ffff0000080fb148 ((wq_completion)async){+.+.}-{0:0}, at: process_one_work+0x190/0x62c [ 4.250180] OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value. [ 4.254094] gregkh#1: ffff80008299bd80 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x1b8/0x62c [ 4.254109] gregkh#2: ffff00000920c8f8 [ 4.258345] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'bitclock-master' with a value. [ 4.264803] (&dev->mutex){....}-{4:4}, at: __device_attach_async_helper+0x3c/0xdc [ 4.264820] gregkh#3: ffff00000a50ca40 (request_class#2){+.+.}-{4:4}, at: __setup_irq+0xa0/0x690 [ 4.264840] gregkh#4: [ 4.268872] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'frame-master' with a value. [ 4.273275] ffff00000a50c8c8 (lock_class){....}-{2:2}, at: __setup_irq+0xc4/0x690 [ 4.296130] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz [ 4.304082] stack backtrace: [ 4.304086] CPU: 1 UID: 0 PID: 76 Comm: kworker/u8:5 Not tainted 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 [ 4.304092] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 4.304097] Workqueue: async async_run_entry_fn [ 4.304106] Call trace: [ 4.304110] show_stack+0x14/0x20 (C) [ 4.304122] dump_stack_lvl+0x6c/0x90 [ 4.304131] dump_stack+0x14/0x1c [ 4.304138] __lock_acquire+0xdfc/0x1584 [ 4.426274] lock_acquire+0x1c4/0x33c [ 4.429942] _raw_spin_lock_irqsave+0x5c/0x80 [ 4.434307] gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.440061] gpio_rcar_irq_set_type+0xd4/0xd8 [ 4.444422] __irq_set_trigger+0x5c/0x178 [ 4.448435] __setup_irq+0x2e4/0x690 [ 4.452012] request_threaded_irq+0xc4/0x190 [ 4.456285] devm_request_threaded_irq+0x7c/0xf4 [ 4.459398] ata1: link resume succeeded after 1 retries [ 4.460902] mmc_gpiod_request_cd_irq+0x68/0xe0 [ 4.470660] mmc_start_host+0x50/0xac [ 4.474327] mmc_add_host+0x80/0xe4 [ 4.477817] tmio_mmc_host_probe+0x2b0/0x440 [ 4.482094] renesas_sdhi_probe+0x488/0x6f4 [ 4.486281] renesas_sdhi_internal_dmac_probe+0x60/0x78 [ 4.491509] platform_probe+0x64/0xd8 [ 4.495178] really_probe+0xb8/0x2a8 [ 4.498756] __driver_probe_device+0x74/0x118 [ 4.503116] driver_probe_device+0x3c/0x154 [ 4.507303] __device_attach_driver+0xd4/0x160 [ 4.511750] bus_for_each_drv+0x84/0xe0 [ 4.515588] __device_attach_async_helper+0xb0/0xdc [ 4.520470] async_run_entry_fn+0x30/0xd8 [ 4.524481] process_one_work+0x210/0x62c [ 4.528494] worker_thread+0x1ac/0x340 [ 4.532245] kthread+0x10c/0x110 [ 4.535476] ret_from_fork+0x10/0x20 Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250121135833.3769310-1-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> [PL: manullay applied the changes] Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Pavel Machek <pavel@denx.de> # for 5.10-stable Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

… stack growth [ Upstream commit 78dcdff ] with commit e2ca070 ("net: sched: protect against stack overflow in TC act_mirred"), act_mirred protected itself against excessive stack growth using per_cpu counter of nested calls to tcf_mirred_act(), and capping it to MIRRED_RECURSION_LIMIT. However, such protection does not detect recursion/loops in case the packet is enqueued to the backlog (for example, when the mirred target device has RPS or skb timestamping enabled). Change the wording from "recursion" to "nesting" to make it more clear to readers. CC: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> [ skulkarni: Adjusted patch for file 'act_mirred.c' - hunk gregkh#4/4 wrt the mainline commit ] Stable-dep-of: ca22da2 ("act_mirred: use the backlog for nested calls to mirred ingress") Signed-off-by: Shubham Kulkarni <skulkarni@mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d9cef55 ] BPF CI testing report a UAF issue: [ 16.446633] BUG: kernel NULL pointer dereference, address: 000000000000003 0 [ 16.447134] #PF: supervisor read access in kernel mod e [ 16.447516] #PF: error_code(0x0000) - not-present pag e [ 16.447878] PGD 0 P4D 0 [ 16.448063] Oops: Oops: 0000 [gregkh#1] PREEMPT SMP NOPT I [ 16.448409] CPU: 0 UID: 0 PID: 9 Comm: kworker/0:1 Tainted: G OE 6.13.0-rc3-g89e8a75fda73-dirty gregkh#4 2 [ 16.449124] Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODUL E [ 16.449502] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/201 4 [ 16.450201] Workqueue: smc_hs_wq smc_listen_wor k [ 16.450531] RIP: 0010:smc_listen_work+0xc02/0x159 0 [ 16.452158] RSP: 0018:ffffb5ab40053d98 EFLAGS: 0001024 6 [ 16.452526] RAX: 0000000000000001 RBX: 0000000000000002 RCX: 000000000000030 0 [ 16.452994] RDX: 0000000000000280 RSI: 00003513840053f0 RDI: 000000000000000 0 [ 16.453492] RBP: ffffa097808e3800 R08: ffffa09782dba1e0 R09: 000000000000000 5 [ 16.453987] R10: 0000000000000000 R11: 0000000000000000 R12: ffffa0978274640 0 [ 16.454497] R13: 0000000000000000 R14: 0000000000000000 R15: ffffa09782d4092 0 [ 16.454996] FS: 0000000000000000(0000) GS:ffffa097bbc00000(0000) knlGS:000000000000000 0 [ 16.455557] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003 3 [ 16.455961] CR2: 0000000000000030 CR3: 0000000102788004 CR4: 0000000000770ef 0 [ 16.456459] PKRU: 5555555 4 [ 16.456654] Call Trace : [ 16.456832] <TASK > [ 16.456989] ? __die+0x23/0x7 0 [ 16.457215] ? page_fault_oops+0x180/0x4c 0 [ 16.457508] ? __lock_acquire+0x3e6/0x249 0 [ 16.457801] ? exc_page_fault+0x68/0x20 0 [ 16.458080] ? asm_exc_page_fault+0x26/0x3 0 [ 16.458389] ? smc_listen_work+0xc02/0x159 0 [ 16.458689] ? smc_listen_work+0xc02/0x159 0 [ 16.458987] ? lock_is_held_type+0x8f/0x10 0 [ 16.459284] process_one_work+0x1ea/0x6d 0 [ 16.459570] worker_thread+0x1c3/0x38 0 [ 16.459839] ? __pfx_worker_thread+0x10/0x1 0 [ 16.460144] kthread+0xe0/0x11 0 [ 16.460372] ? __pfx_kthread+0x10/0x1 0 [ 16.460640] ret_from_fork+0x31/0x5 0 [ 16.460896] ? __pfx_kthread+0x10/0x1 0 [ 16.461166] ret_from_fork_asm+0x1a/0x3 0 [ 16.461453] </TASK > [ 16.461616] Modules linked in: bpf_testmod(OE) [last unloaded: bpf_testmod(OE) ] [ 16.462134] CR2: 000000000000003 0 [ 16.462380] ---[ end trace 0000000000000000 ]--- [ 16.462710] RIP: 0010:smc_listen_work+0xc02/0x1590 The direct cause of this issue is that after smc_listen_out_connected(), newclcsock->sk may be NULL since it will releases the smcsk. Therefore, if the application closes the socket immediately after accept, newclcsock->sk can be NULL. A possible execution order could be as follows: smc_listen_work | userspace ----------------------------------------------------------------- lock_sock(sk) | smc_listen_out_connected() | | \- smc_listen_out | | | \- release_sock | | |- sk->sk_data_ready() | | fd = accept(); | close(fd); | \- socket->sk = NULL; /* newclcsock->sk is NULL now */ SMC_STAT_SERV_SUCC_INC(sock_net(newclcsock->sk)) Since smc_listen_out_connected() will not fail, simply swapping the order of the code can easily fix this issue. Fixes: 3b2dec2 ("net/smc: restructure client and server code in af_smc") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Dust Li <dust.li@linux.alibaba.com> Link: https://patch.msgid.link/20250818054618.41615-1-alibuda@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

These iterations require the read lock, otherwise RCU lockdep will splat: ============================= WARNING: suspicious RCU usage 6.17.0-rc3-00014-g31419c045d64 gregkh#6 Tainted: G O ----------------------------- drivers/base/power/main.c:1333 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 5 locks held by rtcwake/547: #0: 00000000643ab418 (sb_writers#6){.+.+}-{0:0}, at: file_start_write+0x2b/0x3a gregkh#1: 0000000067a0ca88 (&of->mutex#2){+.+.}-{4:4}, at: kernfs_fop_write_iter+0x181/0x24b gregkh#2: 00000000631eac40 (kn->active#3){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x191/0x24b gregkh#3: 00000000609a1308 (system_transition_mutex){+.+.}-{4:4}, at: pm_suspend+0xaf/0x30b gregkh#4: 0000000060c0fdb0 (device_links_srcu){.+.+}-{0:0}, at: device_links_read_lock+0x75/0x98 stack backtrace: CPU: 0 UID: 0 PID: 547 Comm: rtcwake Tainted: G O 6.17.0-rc3-00014-g31419c045d64 gregkh#6 VOLUNTARY Tainted: [O]=OOT_MODULE Stack: 223721b3a80 6089eac6 00000001 00000001 ffffff00 6089eac6 00000535 6086e528 721b3ac0 6003c294 00000000 60031fc0 Call Trace: [<600407ed>] show_stack+0x10e/0x127 [<6003c294>] dump_stack_lvl+0x77/0xc6 [<6003c2fd>] dump_stack+0x1a/0x20 [<600bc2f8>] lockdep_rcu_suspicious+0x116/0x13e [<603d8ea1>] dpm_async_suspend_superior+0x117/0x17e [<603d980f>] device_suspend+0x528/0x541 [<603da24b>] dpm_suspend+0x1a2/0x267 [<603da837>] dpm_suspend_start+0x5d/0x72 [<600ca0c9>] suspend_devices_and_enter+0xab/0x736 [...] Add the fourth argument to the iteration to annotate this and avoid the splat. Fixes: 0679963 ("PM: sleep: Make async suspend handle suppliers like parents") Fixes: ed18738 ("PM: sleep: Make async resume handle consumers like children") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Link: https://patch.msgid.link/20250826134348.aba79f6e6299.I9ecf55da46ccf33778f2c018a82e1819d815b348@changeid Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Merge pull request #2 from gregkh/master

5bee9c7

update

cnspary closed this Sep 17, 2021

cnspary reopened this Sep 17, 2021

cnspary closed this Sep 17, 2021

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Uh oh!

Merge pull request #2 from gregkh/master #4

Merge pull request #2 from gregkh/master #4

Uh oh!

cnspary commented Sep 17, 2021

Uh oh!

Uh oh!

Merge pull request #2 from gregkh/master #4

Merge pull request #2 from gregkh/master #4

Uh oh!

Conversation

cnspary commented Sep 17, 2021

Uh oh!

Uh oh!