Add Creator working branch

ramips: Add support for IODATA WN-G300DGR

Update external interface init according to mapped ports for RTL8367RB:
ext port openwrt#1 = extif0
ext port openwrt#2 = extif1

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>

Driver supports 2 chip versions: RTL8367RB, RTL8367R-VB. Each of them has 2 external ports.
RTL8367RB has ports indexed as openwrt#1,openwrt#2 (PHY openwrt#6, openwrt#7).
RTL8367R-VB has ports indexed as #0,openwrt#1 (PHY openwrt#5,openwrt#6).
Map ports so that extif0 complies to external port 0 or 1 depending on chip ID.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>

Add RGMII mode support for external port openwrt#2 (RTL8367RB)

Add register and masks for external port openwrt#2.
Rewrite method according to Ralink SDK.
Fix bit with bypass line rate.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>

sync

MFW-620 Version and Device parameters

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

Suppress output from `/etc/init.d/service enabled` to avoid corrupting
of the sysupgrade tarball.

Fixes: 0ad062a ("base-files: sysupgrade: add uci-defaults script disabling services openwrt#2")
Signed-off-by: Niall McGee <niall.mcgee@bt.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

The ix4-200d is a 4 bay NAS supported since OpenWrt 23.05. Drive trays
controller. Due to a kernel-related issue with the SATA controller,
trays openwrt#1 and openwrt#2 were not recognized. This issue has been fixed in
kernel 6.10, so with the adoption of kernel 6.12 in the Kirkwood
target trays openwrt#1 and openwrt#2 can now be made accessible. This requires the
kmod-ata-ahci package, which this commit adds as default to the
makefile.

Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: openwrt#19435
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

Every time "sysupgrade -b -" runs it would generate a new
(synthetic) "/etc/uci-defaults/10_disable_services" file with
the current time as the modified time.  This unfortunately
creates a non-deterministic tarball, so if you run a cron job
to save your state, you don't have a trivial way of seeing if
it changed or not without unpacking the archive, deleting this
file, and comparing the entire directory tree to the previous
backup.

Fixes: openwrt#16145
Fixes: 0ad062a ("base-files: sysupgrade: include uci-defaults script disabling services openwrt#2")
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>

Suppress output from `/etc/init.d/service enabled` to avoid corrupting
of the sysupgrade tarball.

Fixes: 0ad062a ("base-files: sysupgrade: add uci-defaults script disabling services openwrt#2")
Signed-off-by: Niall McGee <niall.mcgee@bt.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

The ix4-200d is a 4 bay NAS supported since OpenWrt 23.05. Drive trays
controller. Due to a kernel-related issue with the SATA controller,
trays openwrt#1 and openwrt#2 were not recognized. This issue has been fixed in
kernel 6.10, so with the adoption of kernel 6.12 in the Kirkwood
target trays openwrt#1 and openwrt#2 can now be made accessible. This requires the
kmod-ata-ahci package, which this commit adds as default to the
makefile.

Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: openwrt#19435
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>

QSDK NSS builds utilize skbuff recycling for better handling of memory.

On a Dynalink DL-WRX36 (pbuf script should be set to 'auto') a significant drop in
memory usage was observed as well consistent sustained RX/TX speeds.

BEFORE:
echo 3 >! /proc/sys/vm/drop_caches

free -m
					total        used        free      shared  buff/cache   available
Mem:             867         338         547          90         101         528
Swap:              0           0           0

AFTER:
					total        used        free      shared  buff/cache   available
Mem:             867         242         594           1          81         624
Swap:              0           0           0

NOTE:

For 512MB platforms, users need to test with the following scenarios,
as the patch `999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch` is
really only testable on platforms with 512M or less RAM.

1.) Explicitly setting 'ATH11K_MEM_PROFILE_512M' on and see if system
crashes on boot.

2.) Explicitly setting 'ATH11K_MEM_PROFILE_1G'

3.) Remove patches
999-233-ath11k-Disable-rx_header-tlv-for-2K-SKB.patch
999-311-ath11k-configure-nss-thread-priority-during-pdev_ini.patch

And re-test with openwrt#1 and openwrt#2

It was incorrectly assumed that setting a 512M for 1G platforms would save
memory, instead it needs to be explicitly set to know proper memory
regions, otherwise it would cause fw crash.

Signed-off-by: Sean Khan <datapronix@protonmail.com>