[    7.430207] ath11k c000000.wifi: ipq6018 hw1.0
[    7.430249] ath11k c000000.wifi: FW memory mode: 0
[    7.433873] remoteproc remoteproc0: powering up cd00000.remoteproc
[    7.438478] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340
[    8.311683] remoteproc remoteproc0: remote processor cd00000.remoteproc is now up
[    8.312942] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[    8.318622] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff
[    8.324261] ath11k c000000.wifi: fw_version 0x250a04b8 fw_build_timestamp 2021-12-20 07:20 fw_build_id WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
[   19.032726] ath11k c000000.wifi: failed to wait wlan mode request (mode 7): -110
[   19.032791] ath11k c000000.wifi: qmi failed to send wlan fw mode: -110
[   23.910553] qcom-q6v5-wcss-pil cd00000.remoteproc: watchdog received:
[   23.910553] QC Image Version: QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
[   23.910553] Image Variant : IMAGE_VARIANT_STRING=6018.wlanfw.evalQ
[   23.910553]
[   23.910553]     :Excep  :0 Exception detectedparam0 :zero, param1 :zero, param2 :zero.
[   23.910553] Thread ID      : 0x00000061  Thread name    : WLAN_SCHED1  Process ID     : 0
[   23.910553] Register:
[   23.910553] SP : 0x4bb89a28
[   23.910553] FP : 0x4bb89a40
[   23.910553] PC : 0x4ad9b984
[   23.910553] SSR : 0x00000003
[   23.910553] BADVA : 0x00000004
[   23.910553] LR : 0x4ad9b86c
[   23.910553]
[   23.910553] Stack Dump
[   23.910553] from : 0x4bb89a28
[   23.910553] to   : 0x4bb89bc0
[   23.910553]
[   23.956820] remoteproc remoteproc0: crash detected in cd00000.remoteproc: type watchdog
[   23.978967] remoteproc remoteproc0: handling crash #1 in cd00000.remoteproc
[   23.986946] remoteproc remoteproc0: recovering cd00000.remoteproc

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2
S - IMAGE_VARIANT_STRING=IPQ6018LA
S - OEM_IMAGE_VERSION_STRING=crm-ubuntu64
S - Boot Interface: NAND
S - Secure Boot: Off
S - Boot Config @ 0x000a602c = 0x000002e5
S - JTAG ID @ 0x000a607c = 0x001390e1
S - OEM ID @ 0x000a6080 = 0x00000000
S - Serial Number @ 0x000a4128 = 0xcb4a3f56
S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000
S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000
S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021
S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009
S - PBL Patch Ver: 1
S - I-cache: On
S - D-cache: On
B -      3413 - PBL, Start
B -       592 - bootable_media_detect_entry, Start
B -      4335 - bootable_media_detect_success, Start
B -      5143 - elf_loader_entry, Start
B -      5315 - auth_hash_seg_entry, Start
B -      7783 - auth_hash_seg_exit, Start
B -      8278 - elf_segs_hash_verify_entry, Start
B -    110423 - elf_segs_hash_verify_exit, Start
B -    114849 - auth_xbl_sec_hash_seg_entry, Start
B -    114992 - auth_xbl_sec_hash_seg_exit, Start
B -    121545 - xbl_sec_segs_hash_verify_entry, Start
B -    121545 - xbl_sec_segs_hash_verify_exit, Start
B -    122475 - PBL, End
B -    103273 - SBL1, Start
B -    243329 - GCC [RstStat:0x2, RstDbg:0x420100] WDog Stat : 0x4
B -    245799 - clock_init, Start
D -      2836 - clock_init, Delta
B -    254339 - boot_flash_init, Start
D -     26199 - boot_flash_init, Delta
B -    283741 - sbl1_ddr_set_default_params, Start
D -       244 - sbl1_ddr_set_default_params, Delta
B -    290360 - boot_config_data_table_init, Start
D -      4758 - boot_config_data_table_init, Delta - (575 Bytes)
B -    300181 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0
B -    305030 - Image Load, Start
D -      6619 - OEM_MISC Image Loaded, Delta - (0 Bytes)
B -    314363 - Image Load, Start
D -      5063 - PMIC Image Loaded, Delta - (0 Bytes)
B -    322232 - sbl1_ddr_set_params, Start
B -    327204 - CPR configuration: 0x366
B -    330406 - Pre_DDR_clock_init, Start
D -       183 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta

g<break x 002>
<break>

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2
S - IMAGE_VARIANT_STRING=IPQ6018LA
S - OEM_IMAGE_VERSION_STRING=crm-ubuntu64
S - Boot Interface: NAND
S - Secure Boot: Off
S - Boot Config @ 0x000a602c = 0x000002e5
S - JTAG ID @ 0x000a607c = 0x001390e1
S - OEM ID @ 0x000a6080 = 0x00000000
S - Serial Number @ 0x000a4128 = 0xcb4a3f56
S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000
S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000
S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021
S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009
S - PBL Patch Ver: 1
S - I-cache: On
S - D-cache: On
B -      3413 - PBL, Start
B -       592 - bootable_media_detect_entry, Start
B -      4339 - bootable_media_detect_success, Start
B -      5147 - elf_loader_entry, Start
B -      5319 - auth_hash_seg_entry, Start
B -      7785 - auth_hash_seg_exit, Start
B -      8283 - elf_segs_hash_verify_entry, Start
B -    110432 - elf_segs_hash_verify_exit, Start
B -    114856 - auth_xbl_sec_hash_seg_entry, Start
B -    114999 - auth_xbl_sec_hash_seg_exit, Start
B -    121547 - xbl_sec_segs_hash_verify_entry, Start
B -    121548 - xbl_sec_segs_hash_verify_exit, Start
B -    122477 - PBL, End
B -    103273 - SBL1, Start
B -    243359 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4
B -    245799 - clock_init, Start
D -      2836 - clock_init, Delta
B -    254339 - boot_flash_init, Start
D -     26199 - boot_flash_init, Delta
B -    283772 - sbl1_ddr_set_default_params, Start
D -       213 - sbl1_ddr_set_default_params, Delta
B -    290390 - boot_config_data_table_init, Start
D -      4727 - boot_config_data_table_init, Delta - (575 Bytes)
B -    300242 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0
B -    305091 - Image Load, Start
D -      6618 - OEM_MISC Image Loaded, Delta - (0 Bytes)
B -    314394 - Image Load, Start
D -      5063 - PMIC Image Loaded, Delta - (0 Bytes)
B -    322293 - sbl1_ddr_set_params, Start
B -    327265 - CPR configuration: 0x366
B -    330467 - Pre_DDR_clock_init, Start
D -       183 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    367098 - Image Load, Start
D -       457 - APDP Image Loaded, Delta - (0 Bytes)
B -    380213 - Image Load, Start
D -       458 - QTI_MISC Image Loaded, Delta - (0 Bytes)
B -    382622 - Image Load, Start
D -       824 - Auth Metadata
D -       671 - Segments hash check
D -     22235 - QSEE Dev Config Image Loaded, Delta - (36354 Bytes)
B -    406839 - Image Load, Start
D -      6588 - Auth Metadata
D -     10492 - Segments hash check
D -    329735 - QSEE Image Loaded, Delta - (1470632 Bytes)
B -    737002 - Image Load, Start
D -       671 - Auth Metadata
D -       976 - Segments hash check
D -     34465 - RPM Image Loaded, Delta - (102664 Bytes)
B -    773175 - Image Load, Start
D -       702 - Auth Metadata
D -      3202 - Segments hash check
D -    119011 - APPSBL Image Loaded, Delta - (561320 Bytes)
B -    907802 - SBL1, End
D -    804834 - SBL1, Delta
S - Flash Throughput, 5000 KB/s  (2171545 Bytes,  423057 us)
S - Core 0 Frequency, 800 MHz
S - DDR Frequency, 466 MHz


U-Boot 2016.01 (Mar 18 2020 - 13:15:21 +0800)

CBT U-Boot ver: 2.3.01  ([IPQ6018].[SPF11.CSU1].[code version])

DRAM:  smem ram ptable found: ver: 2 len: 4
512 MiB
NAND:  ONFI device found
ID = 1590aac2
Vendor = c2
Device = aa
SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC:   sdhci: Node Not found, skipping initialization

PCI0 is not defined in the device tree
In:    serial@78B1000
Out:   serial@78B1000
Err:   serial@78B1000
machid: 8030200
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid

Updating boot_count ... done

Hit any key to stop autoboot:  1 <0x08><0x08><0x08> 0 
Setting bus to 0
Valid chip addresses: 62 70

NAND read: device 0 offset 0x6680000, size 0x800000
 8388608 bytes read: OK
## Loading kernel from FIT Image at 44000000 ...
   Using 'config@1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-5.15.90
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x440000e8
     Data Size:    6595018 Bytes = 6.3 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41000000
     Entry Point:  0x41000000
     Hash algo:    crc32
     Hash value:   516526c2
     Hash algo:    sha1
     Hash value:   497007f2d4415e6aed796e9d565301e265a47baa
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
   Using 'config@1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt linksys_mr7350 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x4464a3f4
     Data Size:    28041 Bytes = 27.4 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   c4239d05
     Hash algo:    sha1
     Hash value:   245b31b9d4645772705938d05ed0e1b001134ecc
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x4464a3f4
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 484f6000, end 484ffd88 ... OK
Could not find PCI in device tree
Using machid 0x8030200 from environment

Starting kernel ...

Jumping to AARCH64 kernel via monitor
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x51af8014]
[    0.000000] Linux version 5.15.90 (vladdrako@Vladdrako-PC) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r23642+84-b516753508) 11.3.0, GNU ld (GNU Binutils) 2.39) #0 SMP Fri Jan 27 13:06:44 2023
[    0.000000] Machine model: Linksys MR7350
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000040ffffff]
[    0.000000]   node   0: [mem 0x0000000041000000-0x000000004a5fffff]
[    0.000000]   node   0: [mem 0x000000004a600000-0x000000004fffffff]
[    0.000000]   node   0: [mem 0x0000000050000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 18 pages/cpu s34008 r8192 d31528 u73728
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwait root=/dev/ubiblock0_1 swiotlb=1 coherent_pool=2M
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 389184K/524288K available (10240K kernel code, 1046K rwdata, 3000K rodata, 1536K init, 313K bss, 135104K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[    0.000000] arch_timer: cp15 and mmio timer(s) running at 24.00MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000123] Console: colour dummy device 80x25
[    0.000454] printk: console [tty0] enabled
[    0.000492] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000519] pid_max: default: 32768 minimum: 301
[    0.000680] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.000706] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.002233] rcu: Hierarchical SRCU implementation.
[    0.002399] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.002804] smp: Bringing up secondary CPUs ...
[    0.003396] Detected VIPT I-cache on CPU1
[    0.003459] CPU1: Booted secondary processor 0x0000000001 [0x51af8014]
[    0.004051] Detected VIPT I-cache on CPU2
[    0.004090] CPU2: Booted secondary processor 0x0000000002 [0x51af8014]
[    0.004647] Detected VIPT I-cache on CPU3
[    0.004682] CPU3: Booted secondary processor 0x0000000003 [0x51af8014]
[    0.004746] smp: Brought up 1 node, 4 CPUs
[    0.004814] SMP: Total of 4 processors activated.
[    0.004827] CPU features: detected: 32-bit EL0 Support
[    0.004840] CPU features: detected: CRC32 instructions
[    0.004907] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.005063] CPU: All CPU(s) started at EL1
[    0.005092] alternatives: patching kernel code
[    0.010531] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.010582] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.010752] pinctrl core: initialized pinctrl subsystem
[    0.011586] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.012390] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    0.012706] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.013020] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.013445] thermal_sys: Registered thermal governor 'step_wise'
[    0.013783] cpuidle: using governor menu
[    0.014069] ASID allocator initialised with 65536 entries
[    0.019301] gpio-493 (usb-power-gpio): hogged as output/high
[    0.076107] cryptd: max_cpu_qlen set to 1000
[    0.080144] raid6: skip pq benchmark and using algorithm neonx8
[    0.080178] raid6: using neon recovery algorithm
[    0.080758] SCSI subsystem initialized
[    0.080929] usbcore: registered new interface driver usbfs
[    0.080981] usbcore: registered new interface driver hub
[    0.081027] usbcore: registered new device driver usb
[    0.081331] qcom_scm: convention: smc arm 64
[    0.082700] clocksource: Switched to clocksource arch_sys_counter
[    0.086351] NET: Registered PF_INET protocol family
[    0.086475] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.087030] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.087068] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.087094] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.087154] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    0.087241] TCP: Hash tables configured (established 4096 bind 4096)
[    0.087328] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.087364] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.087509] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.087547] PCI: CLS 0 bytes, default 64
[    0.088688] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[    0.093126] zblock: loaded
[    0.093530] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.093561] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (CMODE_SIZE) (c) 2001-2006 Red Hat, Inc.
[    0.147945] xor: measuring software checksum speed
[    0.154474]    8regs           :  1577 MB/sec
[    0.159755]    32regs          :  1868 MB/sec
[    0.166303]    arm64_neon      :  1507 MB/sec
[    0.166317] xor: using function: 32regs (1868 MB/sec)
[    0.167723] qcom-qmp-phy 78000.ssphy: supply vdda-phy not found, using dummy regulator
[    0.167909] qcom-qmp-phy 78000.ssphy: supply vdda-pll not found, using dummy regulator
[    0.168754] qcom-qmp-phy 78000.ssphy: Registered Qcom-QMP phy
[    0.169254] qcom-qusb2-phy 79000.qusb: supply vdda-pll not found, using dummy regulator
[    0.169384] qcom-qusb2-phy 79000.qusb: supply vdda-phy-dpdm not found, using dummy regulator
[    0.169547] qcom-qusb2-phy 79000.qusb: Registered Qcom-QUSB2 phy
[    0.172076] bam-dma-engine 704000.dma-controller: num-channels unspecified in dt
[    0.172114] bam-dma-engine 704000.dma-controller: num-ees unspecified in dt
[    0.176474] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.177182] msm_serial 78b1000.serial: msm_serial: detected port #0
[    0.177226] msm_serial 78b1000.serial: uartclk = 1843200
[    0.177273] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 20, base_baud = 115200) is a MSM
[    0.177312] msm_serial: console setup on port #0
[    0.861520] printk: console [ttyMSM0] enabled
[    0.866554] msm_serial: driver initialized
[    0.926975] lrng_selftest: LRNG self-tests passed
[    0.927940] loop: module loaded
[    0.932024] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa
[    0.933630] nand: Macronix MX30UF2G18AC
[    0.940200] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.943791] Block protection check failed
[    0.970805] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.970864] ehci-pci: EHCI PCI platform driver
[    0.976326] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.980684] ohci-pci: OHCI PCI platform driver
[    0.986922] usbcore: registered new interface driver usb-storage
[    0.991332] udc-core: couldn't find an available UDC - added [g_mass_storage] to list of pending drivers
[    0.997611] i2c_dev: i2c /dev entries driver
[    1.009154] sdhci: Secure Digital Host Controller Interface driver
[    1.011143] sdhci: Copyright(c) Pierre Ossman
[    1.017262] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.026065] remoteproc remoteproc0: releasing cd00000.remoteproc
[    1.029414] NET: Registered PF_INET6 protocol family
[    1.034166] Segment Routing with IPv6
[    1.038237] In-situ OAM (IOAM) with IPv6
[    1.041824] NET: Registered PF_PACKET protocol family
[    1.045847] 8021q: 802.1Q VLAN Support v1.8
[    1.053815] zswap: loaded using pool zstd/zblock
[    1.056222] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no
[    1.074792] lrng_drng_drbg: DRBG with aes core allocated
[    1.074862] lrng_drng_drbg: DRBG with aes core allocated
[    1.079181] lrng_drng_mgr: Initial DRNG initialized triggering first seeding
[    1.101423] lrng_hash_kcapi: Hash sha512 allocated
[    1.101473] lrng_switch: Conditioning function allocated for DRNG for NUMA node 0
[    1.108430] s2: supplied by regulator-dummy
[    1.113064] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa
[    1.113660] l2: supplied by regulator-dummy
[    1.116656] nand: Macronix MX30UF2G18AC
[    1.127150] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.130995] Block protection check failed
[    1.138694] 20 qcomsmem partitions found on MTD device qcom_nand.0
[    1.142704] Creating 20 MTD partitions on "qcom_nand.0":
[    1.148768] 0x000000000000-0x000000180000 : "0:sbl1"
[    1.171714] lrng_es_mgr: LRNG initial entropy level 48 bits of entropy
[    1.172609] 0x000000180000-0x000000280000 : "0:mibib"
[    1.178458] 0x000000280000-0x000000600000 : "0:qsee"
[    1.185301] 0x000000600000-0x000000680000 : "0:devcfg"
[    1.188170] 0x000000680000-0x000000700000 : "0:rpm"
[    1.193065] 0x000000700000-0x000000780000 : "0:cdt"
[    1.197797] 0x000000780000-0x000000800000 : "0:appsblenv"
[    1.202780] 0x000000800000-0x000000980000 : "0:appsbl"
[    1.209037] 0x000000980000-0x000000a00000 : "0:art"
[    1.213285] 0x000000a00000-0x000001300000 : "0:wififw"
[    1.217291] lrng_es_mgr: LRNG minimally seeded with 129 bits of entropy
[    1.224833] 0x000001300000-0x000001380000 : "0:ethphyfw"
[    1.229758] 0x000001380000-0x000001400000 : "u_env"
[    1.235331] 0x000001400000-0x000001440000 : "s_env"
[    1.239704] 0x000001440000-0x000001480000 : "devinfo"
[    1.244624] 0x000001480000-0x000001c80000 : "kernel"
[    1.269050] lrng_es_mgr: LRNG fully operational
[    1.269081] lrng_es_mgr: LRNG fully seeded with 272 bits of entropy
[    1.275498] 0x000001c80000-0x000006680000 : "rootfs"
[    1.349536] mtd: setting mtd15 (rootfs) as root device
[    1.349829] mtdsplit: no squashfs found in "rootfs"
[    1.353631] 0x000006680000-0x000006e80000 : "alt_kernel"
[    1.364554] 0x000006e80000-0x00000b880000 : "alt_rootfs"
[    1.418980] 0x00000b880000-0x00000ba80000 : "sysdiag"
[    1.420918] 0x00000ba80000-0x00000fe80000 : "syscfg"
[    1.480717] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 24000 KHz, changing to: 864000 KHz
[    1.482752] remoteproc remoteproc0: cd00000.remoteproc is available
[    1.490700] ubi0: attaching mtd17
[    1.824019] ubi0: scanning is finished
[    1.830203] ubi0: attached mtd17 (name "alt_rootfs", size 74 MiB)
[    1.830256] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.835332] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.842061] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.848939] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0
[    1.855697] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.861943] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1674824804
[    1.868990] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 40
[    1.878299] ubi0: background thread "ubi_bgt0d" started, PID 488
[    1.899334] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.900110] Freeing unused kernel memory: 1536K
[    1.962800] Run /sbin/init as init process
[    2.142837] init: Console is alive
[    2.142995] init: - watchdog -
[    2.652775] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.779847] ssdk_switch_device_num_init[1335]:INFO:ess-switch dts node number: 1
[    2.779944] ssdk_dt_get_switch_node[1124]:INFO:ess-switch DT exist!
[    2.786355] ssdk_dt_parse_access_mode[999]:INFO:switch_access_mode: local bus
[    2.792311] ssdk_dt_parse_access_mode[1012]:INFO:switchreg_base_addr: 0x3a000000
[    2.799610] ssdk_dt_parse_access_mode[1013]:INFO:switchreg_size: 0x1000000
[    2.807072] ssdk_dt_parse_mac_mode[327]:INFO:mac mode = 0x0
[    2.813752] ssdk_dt_parse_mac_mode[336]:INFO:mac mode1 = 0xff
[    2.819218] ssdk_dt_parse_mac_mode[345]:INFO:mac mode2 = 0xff
[    2.825173] ssdk_dt_parse_uniphy[364]:INFO:ess-uniphy DT exist!
[    2.831068] ssdk_plat_init[1692]:INFO:ssdk_plat_init start
[    2.953708] ssdk_gcc_clock_init[1275]:INFO:SSDK gcc clock init successfully!
[    2.955999] malibu_phy_api_ops_init[2846]:INFO:qca probe malibu phy driver succeeded!
[    3.007520] regi_init[3953]:INFO:Initializing HPPE!!
[    3.242704] ssdk_ppe_reset_init[1535]:INFO:ppe reset successfully!
[    3.245850] qca_hppe_portctrl_hw_init[123]:INFO:Cypress PPE port initializing
[    3.383437] __adpt_hppe_uniphy_psgmii_mode_set[1067]:INFO:uniphy 0 psgmii channel selection
[    3.610230] ssdk_switch_register[2017]:INFO:Chip version 0x1501
[    3.610262] qca_link_polling_select[1487]:INFO:link-polling-required node does not exist
[    3.614965] ssdk_switch_register[2043]:INFO:polling is selected
[    3.623291] regi_init[3957]:INFO:Initializing HPPE Done!!
[    3.628995] ssdk_genl_init[211]:INFO:ssdk genl family register success.
[    3.634495] regi_init[4020]:INFO:qca-ssdk module init succeeded!
[    3.643086] EDMA ver 1 hw init
[    3.647373] EDMA HW Reset completed succesfully
[    3.650041] Num rings - TxDesc:1 (23-23) TxCmpl:1 (23-23)
[    3.654453] RxDesc:1 (15-15) RxFill:1 (7-7)
[    3.661013] Generic PHY 90000.mdio-1:00: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:00, irq=POLL)
[    3.664622] nss-dp 3a001000.dp eth0: Registered netdev eth0(qcom-id:1)
[    3.673906] GMAC2(ffffff80033228c0) Invalid MAC@ - using 9e:9d:8c:56:c8:28
[    3.680765] Generic PHY 90000.mdio-1:01: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:01, irq=POLL)
[    3.687620] nss-dp 3a001200.dp eth1: Registered netdev eth1(qcom-id:2)
[    3.696820] GMAC3(ffffff8003eb88c0) Invalid MAC@ - using 96:3d:0e:75:bd:eb
[    3.703698] Generic PHY 90000.mdio-1:02: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:02, irq=POLL)
[    3.710513] nss-dp 3a001400.dp eth2: Registered netdev eth2(qcom-id:3)
[    3.719722] GMAC4(ffffff80033238c0) Invalid MAC@ - using 6e:e4:9d:7a:f4:d3
[    3.726609] Generic PHY 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL)
[    3.733430] nss-dp 3a001600.dp eth3: Registered netdev eth3(qcom-id:4)
[    3.742621] GMAC5(ffffff80033248c0) Invalid MAC@ - using 22:60:b4:7f:fd:05
[    3.749549] Generic PHY 90000.mdio-1:04: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:04, irq=POLL)
[    3.756349] nss-dp 3a001800.dp eth4: Registered netdev eth4(qcom-id:5)
[    3.765537] **********************************************************
[    3.771807] * NSS Data Plane driver
[    3.778317] **********************************************************
[    3.785192] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.788320] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[    3.794683] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000000010010
[    3.801361] xhci-hcd xhci-hcd.0.auto: irq 83, io mem 0x08a00000
[    3.810808] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[    3.816606] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[    3.822162] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[    3.830105] hub 1-0:1.0: USB hub found
[    3.836338] hub 1-0:1.0: 1 port detected
[    3.852962] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.853345] hub 2-0:1.0: USB hub found
[    3.860164] hub 2-0:1.0: 1 port detected
[    3.885544] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.890604] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.447488] UBIFS (ubi0:2): Mounting in unauthenticated mode
[    6.447614] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 689
[    6.473805] nss-dp 3a001000.dp eth0: PHY Link up speed: 1000
[    6.473877] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    6.476797] UBIFS (ubi0:2): recovery needed
[    6.550376] UBIFS (ubi0:2): recovery completed
[    6.550502] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[    6.553759] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    6.561636] UBIFS (ubi0:2): FS size: 52060160 bytes (49 MiB, 410 LEBs), max 420 LEBs, journal size 2666496 bytes (2 MiB, 21 LEBs)
[    6.571547] UBIFS (ubi0:2): reserved for root: 2458930 bytes (2401 KiB)
[    6.583170] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 46CB7A48-8FF5-44CF-B72E-BFA0B490231B, small LPT model
[    6.590592] mount_root: overlay filesystem has not been fully initialized yet
[    6.607224] mount_root: switching to ubifs overlay
[    6.610624] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[    6.614458] urandom-seed: Seed file not found (/etc/urandom.seed)
[    6.657032] nss-dp 3a001000.dp eth0: PHY Link is down
[    6.660787] procd: - early -
[    6.661131] procd: - watchdog -
[    7.215253] procd: - watchdog -
[    7.215561] procd: - ubus -
[    7.276023] procd: - init -
Please press Enter to activate this console.
[    7.404406] kmodloader: loading kernel modules from /etc/modules.d/*
[    7.409803] qca-nss-drv.ko is loaded for symbol link
[    7.411798] <NSS-CRYPTO>:module loaded Build_ID - 01/27/23, 20:33:23 SoC=ipq60xx_64
[    7.414949] <NSS-CRYPTO>:module loaded for symbol link
[    7.424522] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2
[    7.427374] Backport generated by backports.git v5.15.81-1-41-g02e352527db5
[    7.440351] NET: Registered PF_QIPCRTR protocol family
[    7.471873] PPP generic driver version 2.4.2
[    7.472656] NET: Registered PF_PPPOX protocol family
[    7.482010] ath11k c000000.wifi: ipq6018 hw1.0
[    7.482052] ath11k c000000.wifi: FW memory mode: 0
[    7.485619] remoteproc remoteproc0: powering up cd00000.remoteproc
[    7.490289] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340
[    8.366636] remoteproc remoteproc0: remote processor cd00000.remoteproc is now up
[    8.367631] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[    8.373599] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff
[    8.379196] ath11k c000000.wifi: fw_version 0x250a04b8 fw_build_timestamp 2021-12-20 07:20 fw_build_id WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
[   19.032741] ath11k c000000.wifi: failed to wait wlan mode request (mode 7): -110
[   19.032806] ath11k c000000.wifi: qmi failed to send wlan fw mode: -110
[   23.963562] qcom-q6v5-wcss-pil cd00000.remoteproc: watchdog received: 
[   23.963562] QC Image Version: QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
[   23.963562] Image Variant : IMAGE_VARIANT_STRING=6018.wlanfw.evalQ
[   23.963562] 
[   23.963562]     :Excep  :0 Exception detectedparam0 :zero, param1 :zero, param2 :zero.
[   23.963562] Thread ID      : 0x00000061  Thread name    : WLAN_SCHED1  Process ID     : 0
[   23.963562] Register:
[   23.963562] SP : 0x4bb89a28
[   23.963562] FP : 0x4bb89a40
[   23.963562] PC : 0x4ad9b984
[   23.963562] SSR : 0x00000003
[   23.963562] BADVA : 0x00000000
[   23.963562] LR : 0x4ad9b86c
[   23.963562] 
[   23.963562] Stack Dump
[   23.963562] from : 0x4bb89a28
[   23.963562] to   : 0x4bb89bc0
[   23.963562] 
[   24.009830] remoteproc remoteproc0: crash detected in cd00000.remoteproc: type watchdog
[   24.031977] remoteproc remoteproc0: handling crash #1 in cd00000.remoteproc
[   24.039955] remoteproc remoteproc0: recovering cd00000.remoteproc

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2
S - IMAGE_VARIANT_STRING=IPQ6018LA
S - OEM_IMAGE_VERSION_STRING=crm-ubuntu64
S - Boot Interface: NAND
S - Secure Boot: Off
S - Boot Config @ 0x000a602c = 0x000002e5
S - JTAG ID @ 0x000a607c = 0x001390e1
S - OEM ID @ 0x000a6080 = 0x00000000
S - Serial Number @ 0x000a4128 = 0xcb4a3f56
S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000
S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000
S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021
S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009
S - PBL Patch Ver: 1
S - I-cache: On
S - D-cache: On
B -      3413 - PBL, Start
B -       592 - bootable_media_detect_entry, Start
B -      4335 - bootable_media_detect_success, Start
B -      5143 - elf_loader_entry, Start
B -      5315 - auth_hash_seg_entry, Start
B -      7783 - auth_hash_seg_exit, Start
B -      8280 - elf_segs_hash_verify_entry, Start
B -    110430 - elf_segs_hash_verify_exit, Start
B -    114855 - auth_xbl_sec_hash_seg_entry, Start
B -    114998 - auth_xbl_sec_hash_seg_exit, Start
B -    121549 - xbl_sec_segs_hash_verify_entry, Start
B -    121550 - xbl_sec_segs_hash_verify_exit, Start
B -    122479 - PBL, End
B -    103273 - SBL1, Start
B -    243329 - GCC [RstStat:0x2, RstDbg:0x420100] WDog Stat : 0x4
B -    245769 - clock_init, Start
D -      2836 - clock_init, Delta
B -    254339 - boot_flash_init, Start
D -     26199 - boot_flash_init, Delta
B -    283741 - sbl1_ddr_set_default_params, Start
D -       244 - sbl1_ddr_set_default_params, Delta
B -    290360 - boot_config_data_table_init, Start
D -      4758 - boot_config_data_table_init, Delta - (575 Bytes)
B -    300181 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:0
B -    305030 - Image Load, Start
D -      6619 - OEM_MISC Image Loaded, Delta - (0 Bytes)
B -    314363 - Image Load, Start
D -      5063 - PMIC Image Loaded, Delta - (0 Bytes)
B -    322232 - sbl1_ddr_set_params, Start
B -    327204 - CPR configuration: 0x366
B -    330406 - Pre_DDR_clock_init, Start
D -       183 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta